ECD SYSTEM (w/o EGR Cooler Bypass Valve), Diagnostic DTC:P0617

DTC Code DTC Name
P0617 Starter Relay Circuit High

DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) for more than 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617

When conditions (a), (b) and (c) are met, positive (+B) battery voltage of 10.5 V or more applied to ECM for 20 seconds

(1 trip detection logic):

(a) Vehicle speed is more than 20 km/h (12.4 mph)

(b) Engine speed is more than 1,000 rpm

(c) STA signal is ON

  • Starter relay circuit

  • Ignition switch

  • ECM

WIRING DIAGRAM

A01KGQ9E03

INSPECTION PROCEDURE

Tech Tips


  • The following troubleshooting process is based on the premise that the engine is cranked normally. If the engine will not crank, proceed to the problem symptoms table Click here.

  • Read freeze frame data using an intelligent tester. Freeze frame data records the engine condition when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

Note

After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON and turn the tester ON.

    3. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

    4. Read the values.

      OK
      Ignition Switch Condition Tester Display (Starter Signal)
      ON OFF
      START ON

    OK

    CHECK FOR INTERMITTENT PROBLEMS

    NG

  2. INSPECT IGNITION SWITCH ASSEMBLY


    1. Disconnect the ignition switch connector.

    2. A01KFFAE01

      Measure the resistance of the ignition switch.

      Standard resistance
      Condition Tester Condition Specified Condition
      OFF Between all terminals 1 MΩ or more
      ACC 2 - 3 1 Ω or less
      ON 2 - 4, 6 - 7 1 Ω or less
      START 1 - 2, 2 - 4, 6 - 7, 7 - 8 1 Ω or less

    3. Reconnect the ignition switch connector.


    OK

    READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) Click here

    NG

  3. REPLACE IGNITION SWITCH ASSEMBLY


    NEXT

  4. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON and turn the tester ON.

    3. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

    4. Read the values.

      OK
      Ignition Switch Condition Tester Display (Starter Signal)
      ON OFF
      START ON

    OK

    SYSTEM IS OK

    NG

  5. REPAIR OR REPLACE HARNESS AND CONNECTOR (IGNITION SWITCH - STA TERMINAL OF ECM)


    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON and turn the tester ON.

    3. Clear DTCs Click here.

    4. Drive the vehicle at more than 12.4 mph (20 km/h) for over 20 seconds.

    5. Select the following menu items: Powertrain / Engine and ECT / Data List / DTC.

    6. Read DTCs.

      Result
      Display (DTC Output) Proceed to
      P0617 A
      No DTC B

    B

    SYSTEM IS OK

    A

    REPLACE ECM