ECD SYSTEM (w/o EGR Cooler Bypass Valve), Diagnostic DTC:P2009, P2010

DTC Code DTC Name
P2009 Intake Manifold Runner Control Circuit Low (Bank 1)
P2010 Intake Manifold Runner Control Circuit High (Bank 1)

DESCRIPTION

Refer to DTC P2006 on page Click here

DTC No. DTC Detection Condition Trouble Area
P2009

Open in VSV for swirl control valve circuit for 0.5 seconds

(2 trip detection logic)

  • VSV for swirl control valve

  • Open in VSV for swirl control valve circuit

  • ECM
P2010

Short in VSV for swirl control valve circuit for 0.5 seconds

(2 trip detection logic)

  • VSV for swirl control valve

  • Short in VSV for swirl control valve circuit

  • ECM

WIRING DIAGRAM

Refer to DTC P2006 on page Click here

INSPECTION PROCEDURE

Tech Tips

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.

Note

If the ECM is replaced, the new ECM needs initialization Click here.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE)


    1. A01KIFVE04
      Text in Illustration
      *1 Air
      *2 Air Filter
      *a VSV: ON
      *b VSV: OFF

      Connect an intelligent tester to the DLC3.

    2. Disconnect the vacuum hoses from the VSV for swirl control valve.

    3. Turn the ignition switch ON and turn the tester ON.

    4. Select the following menu items: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.

    5. Check the operation.

      OK
      When VSV for swirl control valve is ON, air from port E flows out through port F.
      When VSV for swirl control valve is OFF, air from port E flows out through air filter.

    6. Reconnect the vacuum hoses to the VSV for swirl control valve.


    OK

    CHECK FOR INTERMITTENT PROBLEMS

    NG

  2. INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)


    1. A01KHW7E07
      Text in Illustration
      *1 VSV for Swirl Control Valve Connector
      *a Component Side
      *b Front View

      Disconnect the S12 VSV for swirl control valve connector.

    2. Measure the resistance of the VSV.

      Standard resistance
      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 37 to 44 Ω

    3. Reconnect the VSV for swirl control valve connector.


    NG

    REPLACE VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE

    OK

  3. INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (POWER SOURCE VOLTAGE)


    1. A01KHW7E07
      Text in Illustration
      *1 VSV for Swirl Control Valve Connector
      *a Component Side
      *b Front View

      Disconnect the S12 VSV for swirl control valve connector.

    2. Turn the ignition switch ON.

    3. Measure the voltage between the terminal of the wire harness side connector and body ground.

      Standard voltage
      Tester Connection Specified Condition
      S12-1 (VSV for swirl control valve) - Body ground 11 to 14 V

    4. Reconnect the VSV Standard resistance connector.


    OK

    CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE - ECM) Click here

    NG

  4. CHECK HARNESS AND CONNECTOR (VSV FOR SWIRL CONTROL VALVE - EFI MAIN RELAY)


    1. A01KHVLE04
      Text in Illustration
      *1 VSV for Swirl Control Valve Connector
      *2 Relay Block No.2
      *3 EFI MAIN Relay
      *a Wire Harness Side
      *b Front View

      Disconnect the S12 VSV for swirl control valve connector.

    2. Remove the EFI MAIN relay from the R/B No. 2.

    3. Check the resistance.

      Standard resistance (Check for open)
      Tester Connections Specified Conditions
      S12-2 - R/B No. 2 (EFI MAIN relay terminal 3) Below 1 Ω
      Standard resistance (Check for short)
      Tester Connections Specified Conditions
      S12-2 or R/B No. 2 (EFI MAIN relay terminal 3) - Body ground 10 kΩor higher

    4. Reconnect the VSV connector.

    5. Reinstall the EFI MAIN relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPAIR OR REPLACE POWER SOURCE CIRCUIT COMPONENTS

  5. CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE - ECM)


    1. A01KF4TE19
      Text in Illustration
      *1 VSV for Swirl Control Valve Connector
      *2 ECM Connector
      *a Wire Harness Side
      *b Front View

      Disconnect the S9 VSV connector.

    2. Disconnect the E6 ECM connector.

    3. Check the resistance.

      Standard resistance (Check for open)
      Tester Connection Specified Condition
      S12-1 - E6-15 (SCV) Below 1 Ω
      Standard resistance (Check for short)
      Tester Connection Specified Condition
      S12-1 or E6-15 (SCV) - Body ground 10 kΩ or higher

    4. Reconnect the VSV for swirl control valve connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE ECM