ECD SYSTEM (w/ DPF), Diagnostic DTC:P2009, P2010

DTC Code DTC Name
P2009 Intake Manifold Runner Control Circuit Low (Bank 1)
P2010 Intake Manifold Runner Control Circuit High (Bank 1)

DESCRIPTION

Refer to DTC P2006 Click here.

P2009
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Open in No. 1 vacuum switching valve (for swirl control valve assembly) circuit for 0.5 seconds (2 trip detection logic).

  • No. 1 vacuum switching valve (for swirl control valve assembly)

  • Open in No. 1 vacuum switching valve (for swirl control valve assembly) circuit

  • ECM
P2010
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Short in No. 1 vacuum switching valve (for swirl control valve assembly) circuit for 0.5 seconds (2 trip detection logic).

  • No. 1 vacuum switching valve (for swirl control valve assembly)

  • Short in No. 1 vacuum switching valve (for swirl control valve assembly) circuit

  • ECM

WIRING DIAGRAM

A01KHRSE05

INSPECTION PROCEDURE

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

  • After replacing the fuel supply pump assembly or suction control valve, the ECM needs initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

Tech Tips

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)

    A01KILGE19
    Text in Illustration
    *a VSV is ON
    *b VSV is OFF
    *c Air
    *d Air Filter
    *e Port E
    *f Port F

    1. Disconnect the vacuum hoses from the No. 1 vacuum switching valve (for swirl control valve assembly).

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON and turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.

    5. Check the VSV operation when it is operated using the intelligent tester.

      OK
      Tester Operation Specified Condition
      VSV ON Air from port E flows out through port F
      VSV OFF Air from port E flows out through air filter

    NG

    INSPECT NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE ASSEMBLY) (RESISTANCE) Click here

    OK

    CHECK FOR INTERMITTENT PROBLEMS Click here

  2. INSPECT NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE ASSEMBLY) (RESISTANCE)


    1. Inspect the No. 1 vacuum switching valve (for swirl control valve assembly) Click here.


    NG

    REPLACE NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE ASSEMBLY) Click here

    OK

  3. CHECK TERMINAL VOLTAGE (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE ASSEMBLY) POWER SOURCE)


    1. A01KFMTE36
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Vacuum Switching Valve (for Swirl Control Valve Assembly))

      Disconnect the No. 1 vacuum switching valve (for swirl control valve assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      V6-2 (SCV+) - Body ground Ignition switch ON 11 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE ASSEMBLY) - EFI MAIN RELAY HOLDER) Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE ASSEMBLY) - ECM)


    1. Disconnect the No. 1 vacuum switching valve (for swirl control valve assembly) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard Resistance
      Tester Connection Condition Specified Condition
      V6-1 (SCV-) - E10-2 (SCV) Always Below 1 Ω
      V6-1 (SCV-) or E10-2 (SCV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  5. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  6. CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE ASSEMBLY) - EFI MAIN RELAY HOLDER)


    1. Remove the EFI MAIN relay from the engine room relay block.

    2. Disconnect the No. 1 vacuum switching valve (for swirl control valve assembly) connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard Resistance
      Tester Connection Condition Specified Condition
      EFI MAIN relay holder 3 - V6-2 (SCV+) Always Below 1 Ω
      EFI MAIN relay holder 3 or V6-2 (SCV+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  7. CHECK ECM POWER SOURCE CIRCUIT


    1. Check the ECM power source circuit Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  8. REPLACE NO. 1 VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE ASSEMBLY)


    1. Replace the No. 1 vacuum switching valve (for swirl control valve assembly) Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  9. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace harness or connector.


    NEXT

  10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Clear the DTCs Click here.

    4. Start the engine and wait for 3 seconds or more.

    5. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

    6. Confirm that the pending DTC is not output again.


    NEXT

    END