DRIVE BELT INSTALLATION


  1. INSTALL NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT (w/ Air Conditioning System)


    1. Install the No. 1 V (cooler compressor to crankshaft pulley) belt.

  2. ADJUST NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT (w/ Air Conditioning System)


    1. Turn the bolt (B) to adjust the tension of the V belt.

    2. Tighten the bolt (A).

      Torque:
      44 N*m  { 450 kgf*cm, 33 ft.*lbf }

    3. Tighten the bolt (B).

      Torque:
      5.9 N*m  { 60 kgf*cm, 52 in.*lbf }

    4. Check that the belt fits properly into the grooves.

      Tech Tips

      Confirm by hand that the belt has not slipped out of the grooves on the bottom of the pulley.

  3. INSTALL FAN AND GENERATOR V BELT


    1. Install the fan and generator V belt.

  4. ADJUST FAN AND GENERATOR V BELT


    1. Turn the bolt (C) to adjust the tension of the V belt.

    2. Tighten the bolts (A) and (B).

      Torque:
      Bolt A
      29 N*m  { 290 kgf*cm, 18 ft.*lbf }
      Bolt B
      55 N*m  { 560 kgf*cm, 38 ft.*lbf }

    3. Tighten the bolt (C).

      Torque:
      5.9 N*m  { 60 kgf*cm, 52 in.*lbf }

    4. Check that the belt fits properly into the grooves.

      Tech Tips

      Confirm by hand that the belt has not slipped out of the grooves on the bottom of the pulley.

  5. INSPECT DRIVE BELT


    1. A01CHS3E02
      Text in Illustration
      *1 Fan Pulley
      *2 Generator
      *3 Crankshaft Pulley

      Check the fan and generator V belt deflection.

      Tech Tips


      • The specified deflection values per belt are shown in the following table.

      • When inspecting the V belt deflection, apply 98 N (10 kgf, 22 lbf) tensile force to it.

      Deflection
      Item Specified Condition
      New belt 10.5 to 12.5 mm (0.413 to 0.492 in.)
      Used belt 12.5 to 16.0 mm (0.492 to 0.630 in.)

      Note


      • Check the V belt deflection at the specified point.

      • When inspecting a belt which has been used for over 5 minutes, apply the used belt specifications.

    2. A01CGPIE02
      Text in Illustration
      *1 Idler Pulley
      *2 A/C Compressor
      *3 Crankshaft Pulley

      Check the No. 1 V (cooler compressor to crankshaft pulley) belt deflection (w/ Air Conditioning System).

      Tech Tips


      • The specified deflection values per belt are shown in the following table.

      • When inspecting the V belt deflection, apply 98 N (10 kgf, 22 lbf) tensile force to it.

      Deflection
      Item Specified Condition
      New belt 8.5 to 10.0 mm (0.335 to 0.394 in.)
      Used belt 10.0 to 12.0 mm (0.394 to 0.472 in.)

      Note


      • Check the V belt deflection at the specified point.

      • When inspecting a belt which has been used for over 5 minutes, apply the used belt specifications.