ECD SYSTEM, Diagnostic DTC:P0120, P0122, P0123

DTC Code DTC Name
P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DESCRIPTION

The throttle position sensor is mounted in the throttle body and detects the throttle valve (intake shutter) opening angle.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened. The ECM judges the vehicle driving conditions from these signals input from terminal VLU, and uses them as one of the conditions for deciding the air fuel ratio correction, power increase correction and fuel cut control, etc.

A01CH7XE07
DTC No. DTC Detection Condition Trouble Area
- Condition of DTC P0120, P0122, or P0123 continues for 0.5 seconds (open or short in throttle position sensor circuit) -
P0120 Open or short in throttle position sensor circuit for 1 second.

  • Open or short in throttle position sensor circuit

  • Throttle position sensor

  • ECM
P0122 Open in throttle position sensor circuit for 1 second.

  • Open in throttle position sensor circuit

  • Throttle position sensor

  • ECM
P0123 Short in throttle position sensor circuit for 1 second.

  • Short in throttle position sensor circuit

  • Throttle position sensor

  • ECM

WIRING DIAGRAM

A01CH6EE04

INSPECTION PROCEDURE

Tech Tips


  • If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

  • Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

PROCEDURE


  1. CHECK ECM (VC VOLTAGE)


    1. A01CGXCE01

      Turn the ignition switch to the ON position.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      E22-18 (VC) - E22-28 (E2) Always 4.5 to 5.5 V

    NG

    REPLACE ECM

    OK

  2. CHECK ECM (VLU VOLTAGE)


    1. A01CGXCE03

      Turn the ignition switch to the ON position.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Accelerator Pedal Condition Specified Condition
      E23-20 (VLU) - E22-28 (E2) Released 2.6 to 3.0 V
      E23-20 (VLU) - E22-28 (E2) Depressed 1.4 to 1.8 V
      E23-20 (VLU) - E22-28 (E2) Released → Depressed Voltage changes constantly

    NG

    INSPECT THROTTLE POSITION SENSOR Click here

    OK

    REPLACE ECM

  3. INSPECT THROTTLE POSITION SENSOR


    1. A01CGRZE06

      Disconnect the throttle position sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Throttle Valve Condition Specified Condition
      T7-3 (V1A) - T7-2 (E2) Fully closed 0.2 to 5.7 kΩ
      T7-3 (V1A) - T7-2 (E2) Fully open 2.0 to 10.2 kΩ

    3. Reconnect the throttle position sensor connector.


    NG

    REPLACE DIESEL THROTTLE BODY

    OK

  4. CHECK HARNESS AND CONNECTOR (ECM - THROTTLE POSITION SENSOR)


    1. A01CGXJE08

      Disconnect the turbo ECM connectors.

    2. Disconnect the throttle position sensor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Check for open
      Tester Connection Condition Specified Condition
      T7-1 (VC) - E22-18 (VC) Always Below 1 Ω
      T7-3 (V1A) - E23-20 (VLU) Always Below 1 Ω
      T7-2 (E2) - E22-28 (E2) Always Below 1 Ω
      Check for short
      Tester Connection Condition Specified Condition
      T7-1 (VC) or E22-18 (VC) - Body ground Always 10 kΩ or higher
      T7-3 (V1A) or E23-20 (VLU) - Body ground Always 10 kΩ or higher

    4. Reconnect the throttle position sensor connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE POSITION SENSOR)

    OK

  5. CHECK DTC OUTPUT


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the ON position.

    3. Turn the tester on.

    4. Enter the following menu items: Powertrain / Engine and ECT / DTC.

    5. Read the DTCs.

      Result
      Display (DTC output) Proceed to
      P0120, P0122 and/or P0123 A
      No output B

    NG

    CHECK FOR INTERMITTENT PROBLEMS

    OK

    REPLACE ECM