ECD SYSTEM, Diagnostic DTC:P0100, P0102, P0103

DTC Code DTC Name
P0100 Mass or Volume Air Flow Circuit
P0102 Mass or Volume Air Flow Circuit Low Input
P0103 Mass or Volume Air Flow Circuit High Input

DESCRIPTION

The Mass Air Flow (MAF) meter uses a platinum hot wire. The hot wire MAF meter consists of a platinum hot wire, thermistor and a control circuit installed in a plastic housing. The hot wire MAF meter works on the principle that the hot wire and thermistor located in the intake air bypass of the housing detect any changes in the IAT.

The hot wire is maintained at the set temperature by controlling current flow through the hot wire. This current flow is then measured as the output voltage of the MAF meter.

The circuit is constructed so that the platinum hot wire and thermistor provide a bridge circuit with the power transistor controlled so that the potential of A and B remains equal to maintain the set temperature.

A01CI1AE01
DTC No. DTC Detection Condition Trouble Area
P0100 Open or short in MAF meter circuit for more than 3 seconds with engine speed at 4000 rpm or less

  • Open or short in MAF meter circuit

  • MAF meter

  • Voltage converter

  • ECM
P0102 Open in MAF meter circuit for more than 3 seconds with engine speed at 4000 rpm or less

  • Open or short in MAF meter circuit

  • MAF meter

  • Voltage converter

  • ECM
P0103 Short in MAF meter circuit for more than 3 seconds with engine speed at 4000 rpm or less

  • Open or short in MAF meter circuit

  • MAF meter

  • Voltage converter

  • ECM

Tech Tips

When DTC P0100, P0102 or P0103 is detected, check the mass air flow ratio by selecting the following menus using the intelligent tester: Powertrain / Engine and ECT / Data List / MAF.

Air Flow Value (gm/sec.) Malfunction
Approx. 0.0

  • Open in MAF meter power source circuit

  • Open
170.1 or more Open in EVG circuit

WIRING DIAGRAM

A01CJBQE04

INSPECTION PROCEDURE

Tech Tips

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (MAF RATE)


    1. Connect the intelligent tester to the DLC3.

    2. Start the engine.

    3. Turn the tester on.

    4. Enter the following menu items: Powertrain / Engine and ECT / Data List / MAF.

    5. Read the value.

      Result
      Air Flow Rate (gm/s) Proceed to
      0.0 A
      170.1 or more B
      Between 1.6 and 170.0* C

      Tech Tips

      *: The value should change when the throttle valve is opened or closed.


    B

    CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) Click here

    C

    CHECK FOR INTERMITTENT PROBLEMS

    A

  2. CHECK MASS AIR FLOW METER (POWER SOURCE)


    1. A01CGWHE11

      Disconnect the MAF meter connector.

    2. Turn the ignition switch to the ON position.

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      A20-1 (+B) - Body ground Always 11 to 14 V

    4. Reconnect the MAF meter connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ENG-3 RELAY)

    OK

  3. INSPECT ECM (VG VOLTAGE)


    1. A01CGXCE10

      Start the engine.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      E23-24 (VG) - E23-32 (EVG) Engine is idling 1.5 to 1.9 V
      E23-24 (VG) - E23-32 (EVG) Engine speed at 3000 rpm 3.0 to 4.0 V

      Tech Tips

      The A/C switch should be turned off.


    NG

    CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) Click here

    OK

    REPLACE ECM

  4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    1. A01CICME07

      Disconnect the MAF meter connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Check for open
      Tester Connection Condition Specified Condition
      A20-3 (VG) - E23-24 (VG) Always Below 1 Ω
      A20-2 (E2G) - E23-32 (EVG) Always Below 1 Ω
      Check for short
      Tester Connection Condition Specified Condition
      A20-3 (VG) or E23-24 (VG) - Body ground Always 10 kΩ or higher

    4. Reconnect the MAF meter connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)

    OK

    REPLACE MASS AIR FLOW METER