FRONT DOOR BELT MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT DOOR OUTER GLASS WEATHERSTRIP LH


    1. Attach the 6 claws to install the front door outer glass weatherstrip LH.

  2. INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER LH


    1. Attach the 3 clips to install a new front door front lower frame upper cover LH.

  3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. w/ Power Window:


      1. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

      2. Connect the cable to the negative (-) battery terminal.

      3. Move the front door window regulator sub-assembly LH so that the front door glass sub-assembly LH can be installed.

      4. Disconnect the cable from the negative (-) battery terminal.

      5. Remove the power window regulator master switch assembly with front door armrest base panel.

    2. w/o Power Window:


      1. Temporarily install the front door window regulator handle assembly.

      2. Move the front door glass sub-assembly LH so that the front door glass bolts can be seen.

    3. A01CIR7E01

      Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.

      Note

      Be careful not to damage the front door glass sub-assembly LH and front door glass run LH.

    4. Install the front door glass sub-assembly LH with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. Apply new butyl tape to the front door panel.

    2. Pass the link and wire harness through a new front door service hole cover LH.

    3. A01CIJ2E01
      Text in Illustration
      *a Reference Point

      Attach the front door service hole cover LH using the reference points on the front door panel.

      Note


      • Securely install the front door service hole cover LH to prevent wrinkles and air bubbles.

      • There should be no wrinkles or folds after installing the front door service hole cover LH.

      • After installing the front door service hole cover LH, check the seal quality.

  5. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. Connect the front door lock remote control link LH to the front door inside handle sub-assembly LH.

    2. A01CI9N

      Slide the front door inside handle sub-assembly LH as shown in the illustration and attach the 2 guides.

    3. Attach the claw to install the front door inside handle sub-assembly LH.

    4. Attach the clamp.

  6. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. Attach the 8 clips to install the front door trim board sub-assembly LH.

    2. Install the clip.

  7. INSTALL DOOR ASSIST GRIP ASSEMBLY LH


    1. Install the door assist grip assembly LH with the 4 bolts.

      Torque:
      19 N*m  { 189 kgf*cm, 14 ft.*lbf }

  8. INSTALL DOOR ASSIST GRIP COVER LH


    1. Attach the 4 claws to install the door assist grip cover LH.

  9. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH


    1. Attach the 4 claws to install the front door inside handle bezel LH.

    2. Install the screw.

  10. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (w/ Power Window)


    1. Connect the connector.

    2. Attach the guide, 2 claws and clip to install the power window regulator master switch assembly with front door armrest base panel.

  11. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. A01CH6LE01
      Text in Illustration
      *1 Snap Ring
      *2 Front Door Regulator Inside Handle Plate
      *a Front Side

      Temporarily install the front door window regulator handle assembly, fully close the window, and then remove the front door window regulator handle assembly.

    2. Install the front door regulator inside handle plate and snap ring to the front door window regulator handle assembly.

    3. Install the front door window regulator handle assembly to the front door window regulator sub-assembly LH as shown in the illustration.

      Standard
      Angle Specified Condition
      A 15 to 45°

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Power Window)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.