DATA LIST
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus:
for Main Body: Body Electrical / Main Body / Data List.
for PCS/LDA/RSA/LVN: Chassis / PCS/LDA/ RSA/LVN / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Automatic High Beam | Automatic high beam system / OFF or ON | OFF: Automatic high beam switch not pressed ON: Automatic high beam switch pressed |
- |
| Dimmer SW | Dimmer switch high position signal / OFF or ON | OFF: Dimmer switch in low position ON: Dimmer switch in high or high flash position |
- |
| Head Light SW (Head) | Light control switch head position signal / OFF or ON | OFF: Light control switch not in head position ON: Light control switch in head position |
- |
| Auto H Beam STS0 | Automatic high beam sensor current state / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err | Condition can be displayed | Undetec: undetected CAM NA: camera detection malfunction* No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: system delay Delay: Delay Aim Lmt: Beam axis deviation SAE Mode: Specialized detection Undefin: Undefined LIN Err: LIN malfunction |
| Auto H Beam STS1 | Automatic high beam sensor state past 1 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err | Condition can be displayed | Undetec: undetected CAM NA: camera detection malfunction* No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: system delay Delay: Delay Aim Lmt: Beam axis deviation SAE Mode: Specialized detection Undefin: Undefined LIN Err: LIN malfunction |
| Auto H Beam STS2 | Automatic high beam sensor state past 2 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err | Condition can be displayed | Undetec: undetected CAM NA: camera detection malfunction* No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: system delay Delay: Delay Aim Lmt: Beam axis deviation SAE Mode: Specialized detection Undefin: Undefined LIN Err: LIN malfunction |
| Auto H Beam STS3 | Automatic high beam sensor state past 3 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err | Condition can be displayed | Undetec: undetected CAM NA: camera detection malfunction* No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: system delay Delay: Delay Aim Lmt: Beam axis deviation SAE Mode: Specialized detection Undefin: Undefined LIN Err: LIN malfunction |
| Auto H Beam STS4 | Automatic high beam sensor state past 4 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err | Condition can be displayed | Undetec: undetected CAM NA: camera detection malfunction* No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: system delay Delay: Delay Aim Lmt: Beam axis deviation SAE Mode: Specialized detection Undefin: Undefined LIN Err: LIN malfunction |
| Auto H Beam STS5 | Automatic high beam sensor state past 5 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err | Condition can be displayed | Undetec: undetected CAM NA: camera detection malfunction* No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: system delay Delay: Delay Aim Lmt: Beam axis deviation SAE Mode: Specialized detection Undefin: Undefined LIN Err: LIN malfunction |
| Auto H Beam STS6 | Automatic high beam sensor state past 6 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err | Condition can be displayed | Undetec: undetected CAM NA: camera detection malfunction* No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: system delay Delay: Delay Aim Lmt: Beam axis deviation SAE Mode: Specialized detection Undefin: Undefined LIN Err: LIN malfunction |
| Auto H Beam STS7 | Automatic high beam sensor state past 7 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mode, Undefin, LIN Err | Condition can be displayed | Undetec: undetected CAM NA: camera detection malfunction* No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: system delay Delay: Delay Aim Lmt: Beam axis deviation SAE Mode: Specialized detection Undefin: Undefined LIN Err: LIN malfunction |
| Number of DTC | Number of trouble codes / 0 to 255 | Condition can be displayed | - |
*: If CAM NA is displayed, the lane departure warning camera may have stopped operating due to high temperature.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Low Temperature Status | Existence of low temperature malfunction / OFF or ON | OFF: Pre-crash safety city sensor low temperature malfunction does not exist ON: Pre-crash safety city sensor low temperature malfunction exists |
- |
| High Temperature Status | Existence of high temperature malfunction / OFF or ON | OFF: Pre-crash safety sensor high temperature malfunction does not exist ON: Pre-crash safety sensor high temperature malfunction exists |
- |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / PCS/LDA/RSA/LVN / Active Test
Perform Active Test according to the display on the GTS.
Tech Tips
The ignition switch must be turned to ON to proceed with the Active Test using the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Automatic High Beam | Operates automatic high beam system | ON / OFF | This Active Test can only be performed when the ignition switch ON, the vehicle is stopped and the area around the vehicle is dark. (Normal system operation conditions, such as vehicle speed and shift lever position, do not need to be met.) |