REAR DOOR REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the RH side.

PROCEDURE


  1. APPLY BODY GREASE

  2. INSTALL NO. 2 BLACK OUT TAPE

    Tech Tips

    Use the same procedure as for the LH side Click here.

  3. INSTALL REAR DOOR WEATHERSTRIP


    1. A01VIMR

      Engage the 29 clips and install the rear door weatherstrip.

    2. Engage the 2 clips.

  4. INSTALL REAR DOOR CHECK ASSEMBLY


    1. Apply MP grease to the sliding areas of the rear door check.

    2. A01VIGH

      Install the rear door check onto the door panel with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    3. Apply adhesive to the threads of the bolt.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    4. Install the front door check onto the body panel with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

  5. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. Apply MP grease to the sliding areas of the rear door outside handle frame.

    2. A01VKTSE02
      Text in Illustration
      *1 Grommet

      Slide the rear door outside handle frame to install it.

    3. Engage the grommet and 2 claws.

    4. A01VLMZ

      Using a "TORX" socket wrench T30, install the rear door outside handle frame with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

  6. INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD


    1. A01VEZ2

      Engage the 2 claws and install the rear door outside handle rear pad.

  7. INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD


    1. A01VFIP

      Engage the 3 claws and install the rear door outside handle front pad.

  8. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. A01VDUC

      Pushing the rear door outside handle in the direction of the arrow mark shown in the illustration, install the rear door outside handle.

  9. INSTALL REAR DOOR OUTSIDE HANDLE COVER


    1. A01VFA4

      Engage the 2 claws and temporarily install the rear door outside handle cover.

    2. A01VDUA

      Using a "TORX" socket wrench T30, install the rear door outside handle cover.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

  10. INSTALL REAR DOOR LOCK ASSEMBLY

    Click here

  11. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

    Tech Tips

    Use the same procedure as for the LH side Click here.

  12. INSTALL REAR DOOR GLASS RUN


    1. A01VEW9

      Engage the 2 guides and install the rear door glass run.

    2. Install the clip.

  13. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)


    1. Apply MP grease to the sliding parts of the rear door window regulator.

    2. Install the temporary bolt.

    3. A01VLZ2E08
      Text in Illustration
      *1 Temporary Bolt

      Insert the rear door window regulator into the door panel. Use the temporary bolt to hang the rear door window regulator on the door panel.

    4. Tighten the 3 bolts and the temporary bolt in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    5. Connect the connector.

  14. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)


    1. A01VFHOE03

      Tighten the 3 bolts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  15. INSTALL REAR DOOR GLASS CHANNEL FILLER


    1. Apply soapy water to a new rear door glass channel filler.

    2. A01VFRME01
      Text in Illustration
      *a Front Side
      *b Rear Side

      Install the new rear door glass channel filler as shown in the illustration.

  16. INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY


    1. Apply soapy water to a rear door glass channel.

    2. A01VDMKE01
      Text in Illustration
      *a Front Side
      *b Rear Side

      Using a plastic-faced hammer, tap the channel onto the glass to install the glass channel.

      Note


      • Be careful not to damage the glass or glass channel.

      • Make sure the position of the rear door glass channel filler does not change.

  17. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A01VIA2E01

      Insert the rear door glass into the rear door panel along the rear door glass run as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the rear door glass.

    2. A01VDJO

      Slide the lower section of the rear door glass as indicated by the arrow as shown in the illustration.

  18. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A01VFYB

      Engage the rear door window division bar to the rear door glass run.

    2. Install the rear door window division bar with the 3 bolts and nut.

      Torque:
      6.2 N*m  { 63 kgf*cm, 55 in.*lbf }

  19. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. A01VKTRE02
      Text in Illustration
      *a Reference Point

      Install a new rear door service hole cover according to the reference points on the rear door panel.

      Tech Tips

      Securely install the rear door service hole cover taking care to prevent wrinkles.

  20. INSTALL REAR SPEAKER ASSEMBLY

    Click here

  21. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP


    1. A01VL66

      Engage the 7 claws and install the rear door glass inner weatherstrip as shown in the illustration.

  22. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01VE7Q

      Engage the 4 guides and install the rear door inside handle.

  23. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01VFADE03
      Text in Illustration
      *1 Rear Door Lock Remote Control Cable Assembly
      *2 Rear Door Inside Locking Cable Assembly

      Connect the rear door lock remote control cable and the rear door inside locking cable to the rear door inside handle.

    2. A01VHZA

      Engage the 7 clips and install the rear door trim board.

    3. A01VESR

      Install the 3 screws.

    4. A01VLF2

      Engage the claw and close the cover.

  24. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)


    1. A01VDVJ

      Connect the connector.

    2. Engage the 9 claws and 3 guides, and install the rear armrest base upper panel.

  25. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)


    1. A01VH8Y

      Engage the 5 claws and 2 guides, and install the front armrest base upper panel.

  26. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. A01VGGKE01
      Text in Illustration
      *a Inside of Vehicle

      Install the window regulator handle plate.

    2. Open all the windows.

    3. A01VDMXE01
      Text in Illustration
      *a Assemble with Glass in Fully Open Position

      Install the rear door window regulator handle with the clip at the angle shown in the illustration.

  27. INSTALL REAR DOOR FRAME GARNISH


    1. A01VKKW

      Engage the guide.

    2. Engage the 2 clips and claw and install the rear door frame garnish.

  28. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  29. INSPECT POWER WINDOW OPERATION (w/ Power Window)

    Click here