REAR DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the RH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  3. REMOVE REAR DOOR FRAME GARNISH


    1. A01VKKW

      Disengage the 2 clips and claw.

    2. Disengage the guide and remove the rear door frame garnish.

  4. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. A01VGP7

      Insert a clip remover between the plate and front door trim board.

    2. Turn the handle with the clip remover inserted, as shown in the illustration.

    3. Remove the front door window regulator handle and clip.

    4. Remove the window regulator handle plate.

  5. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)


    1. A01VDVJ

      Using a moulding remover, disengage the 9 claws and 3 guides.

    2. Disconnect the connector and remove the rear armrest base upper panel.

  6. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)


    1. A01VH8Y

      Using a moulding remover, disengage the 5 claws and 2 guides and remove the rear armrest base upper panel.

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01VL9DE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.

    2. A01VESR

      Remove the 3 screws.

    3. A01VHZA

      Disengage the 7 clips.

    4. A01VFADE03
      Text in Illustration
      *1 Rear Door Lock Remote Control Cable Assembly
      *2 Rear Door Inside Locking Cable Assembly

      Disconnect the rear door lock remote control cable assembly and the rear door inside locking cable assembly and remove the rear door trim board.

  8. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01VE7Q

      Disengage the 4 guides and remove the rear door inside handle.

  9. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP


    1. A01VGOK

      Disengage the 7 claws and remove the rear door glass inner weatherstrip as shown in the illustration.

  10. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  11. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A01VM8U

      Remove the rear door service hole cover.

      Tech Tips

      Remove any tape remaining on the door side.

  12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A01VFYB

      Remove the 3 bolts and nut, and the rear door window division bar.

  13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A01VFWC

      Slide the lower section of the rear door glass as indicated by the arrow as shown in the illustration.

    2. A01VDVXE01

      Remove the rear door glass as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the rear door glass.

  14. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY


    1. A01VETUE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, remove the rear door glass channel.

      Note

      Do not damage the rear door glass.

  15. REMOVE REAR DOOR GLASS CHANNEL FILLER


    1. Remove the rear door glass channel filler.

  16. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)


    1. A01VLZ2E07
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the temporary bolt and the rear door window regulator.

  17. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)


    1. A01VFHO

      Remove the 3 bolts and the rear door window regulator.

      Note

      Do not drop or damage the window regulator when removing the bolts.

  18. REMOVE REAR DOOR GLASS RUN


    1. A01VEW9

      Remove the clip.

    2. Disengage the 2 guides and remove the rear door glass run.

  19. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

    Tech Tips

    Use the same procedure as for the LH side Click here.

  20. REMOVE REAR DOOR LOCK ASSEMBLY

    Click here

  21. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    1. A01VDUA

      Using a "TORX" socket wrench T30, loosen the screw.

    2. A01VFA4

      Disengage the 2 claws and remove the rear door outside handle cover.

  22. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. A01VE6T

      Remove the rear door outside handle in the direction indicated by the arrow as shown in the illustration.

  23. REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD


    1. A01VFIP

      Disengage the 3 claws and remove the rear door outside handle front pad.

  24. REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD


    1. A01VEZ2

      Disengage the 2 claws and remove the rear door outside handle rear pad.

  25. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. A01VLMZ

      Using a "TORX" socket wrench T30, loosen the screw.

    2. A01VLOL

      Slide the rear door outside handle frame and disengage the grommet and 2 claws of the rear door outside handle frame, and then remove it.

  26. REMOVE REAR DOOR CHECK ASSEMBLY


    1. A01VIGH

      Remove the 3 bolts and the rear door check.

  27. REMOVE REAR DOOR WEATHERSTRIP


    1. A01VIMR

      Using a clip remover, disengage the 2 clips.

    2. Using a clip remover, disengage the 29 clips and remove the rear door weatherstrip.

  28. REMOVE NO. 2 BLACK OUT TAPE

    Tech Tips

    Use the same procedure as for the LH side Click here.