READ DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the Intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus:
for D-Door Motor: Body / D-Door Motor / Data List
for Main Body: Body / Main Body / Data List
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| D Door P/W Auto SW | Driver side power window auto switch signal / ON or OFF |
ON: Driver side door power window auto switch operated OFF: Driver side door power window auto switch not operated |
- |
| D Door P/W Up SW | Driver side power window manual up switch signal / ON or OFF ON or OFF |
ON: Driver side door power window manual up switch operated OFF: Driver side door power window manual up switch not operated |
- |
| D Door P/W Down SW | Driver side power window manual down switch signal / ON or OFF |
ON: Driver side door power window manual down switch operated OFF: Driver side door power window manual down switch not operated |
- |
| Glass Position (Close - 1/4) | Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (1/4 - 2/4) | Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (2/4 - 3/4) | Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (3/4 - Open) | Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Number of Trouble Codes | Number of trouble codes / Min.: 0 Max.: 255 |
Number of DTCs will be displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Door Courtesy | Front door courtesy light switch RH signal / ON or OFF |
ON: Front door RH closed OFF: Front door RH opened |
- |
| FL Door Courtesy | Front door courtesy light switch LH signal / ON or OFF |
ON: Front door LH closed OFF: Front door LH opened |
- |
ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the Intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / D-Door Motor / Active Test.
According to the display on the intelligent tester, perform the Active Test.
CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF / UP / DOWN | - |