AIRBAG SYSTEM(w/o Curtain Shield Airbag) TC and CG Terminal Circuit

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

The DTCs are displayed by blinking the SRS warning light.

Tech Tips


  • Make sure that DTCs which relate to the CAN communication system are not output. If any of these DTCs are output, check the CAN communication system Click here.

  • When a warning light keeps blinking, a short to ground in the wiring of terminal TC of the DLC3 or an internal ground short in an ECU is suspected.

  • The DTC output mode signal is transmitted through the CAN to each ECU including the airbag sensor assembly. Thus if no systems enter DTC output mode, the ECM may have a malfunction.

WIRING DIAGRAM

A01VEHVE06

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

    A01VKLFE01

    1. Turn the ignition switch off.

    2. Disconnect the connector from the ECM.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 1NR-FE
      Tester Connection Condition Specified Condition

      F4-13 (TC) -

      A58-23 (TC)

      		 Always Below 1 Ω
      for 1ND-TV
      Tester Connection Condition Specified Condition

      F4-13 (TC) -

      A59-24 (TC)

      		 Always Below 1 Ω
      for 1KR-FE
      Tester Connection Condition Specified Condition

      F4-13 (TC) -

      A93-57 (TC)

      		 Always Below 1 Ω
      Text in Illustration
      *A for 1NR-FE
      *B for 1ND-TV
      *C for 1KR-FE
      *1 DLC3
      *a

      Front view of wire harness connector

      (to ECM)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK HARNESS AND CONNECTOR (CG OF DLC3 - BODY GROUND)


    1. A01VKQCE01
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition

      F4-4 (CG) -

      Body ground

      		 Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (TC OF ECM)


    1. Measure the resistance according to the value(s) in the table below.

      A01VERTE01
      Standard Resistance
      for 1NR-FE
      Tester Connection Condition Specified Condition

      A58-23 (TC) -

      Body ground

      		 Always 1 MΩ or higher
      for 1ND-TV
      Tester Connection Condition Specified Condition

      A59-24 (TC) -

      Body ground

      		 Always 1 MΩ or higher
      for 1KR-FE
      Tester Connection Condition Specified Condition

      A93-57 (TC) -

      Body ground

      		 Always 1 MΩ or higher
      Text in Illustration
      *A for 1NR-FE
      *B for 1ND-TV
      *C for 1KR-FE
      *a

      Front view of wire harness connector

      (to ECM)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE ECM


    1. Replace the ECM.

    2. Check for DTCs of the ECM.


      Result
      Result Proceed to
      Normal code is output A
      DTC is output (for 1NR-FE) B
      DTC is output (for 1ND-TV) C
      DTC is output (for 1KR-FE) D
      DTC output mode is set (except airbag sensor assembly) E

    A

    END

    B

    GO TO INSPECTION PROCEDURE OF DTC OUTPUT Click here

    C

    GO TO INSPECTION PROCEDURE OF DTC OUTPUT Click here

    D

    GO TO INSPECTION PROCEDURE OF DTC OUTPUT Click here

    E

    REPLACE AIRBAG SENSOR ASSEMBLY Click here