AIRBAG SYSTEM(w/ VSC), Diagnostic DTC:B1628/82

DTC Code DTC Name
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete

DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the airbag sensor assembly, side airbag sensor LH and No. 2 side airbag sensor assembly LH.

The side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

This DTC is stored when a malfunction is detected in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No. DTC Detection Condition Trouble Area
B1628/82

  • The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

  • Side airbag sensor assembly LH malfunction

  • No. 2 side airbag sensor assembly LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Side airbag sensor assembly LH

  • No. 2 side airbag sensor assembly LH

  • Airbag sensor assembly

WIRING DIAGRAM

A01VI1PE10
*a Side Airbag Sensor Assembly LH
*b No. 2 Side Airbag Sensor Assembly LH
*c Airbag Sensor Assembly

PROCEDURE


  1. CHECK HISTORY DTC


    1. Turn the ignition switch to ON, and wait for at least 60 seconds.

    2. Check for history DTCs Click here.

      Result
      History DTC B1627/82 or B1637/82 is not output.

      Tech Tips

      Codes other than history DTCs B1627/82 and B1637/82 may be output at this time, but they are not related to this check.


    NG

    INSPECTION PROCEDURE RELEVANT TO OUTPUT DTC Click here

    OK

  2. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

    5. Check that the terminals of connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK FLOOR WIRE (OPEN)


    1. Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

      A01VDP7E02
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH *2 Airbag Sensor Assembly
      *3 Floor Wire *4 Connector B
      *5 Connector C *6 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)

      		 *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-4 (BBL+) - K21-3 (BBL-) Always Below 1 Ω

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK FLOOR WIRE (SHORT)


    1. A01VK7SE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-4 (BBL+) - K21-3 (BBL-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  5. CHECK FLOOR WIRE (SHORT TO B+)


    1. A01VK7SE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K21-4 (BBL+) - Body ground Ignition switch ON Below 1 V
      K21-3 (BBL-) - Body ground Ignition switch ON Below 1 V

    NG

    REPLACE FLOOR WIRE

    OK

  6. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. A01VK7SE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-4 (BBL+) - Body ground Always 1 MΩ or higher
      K21-3 (BBL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  7. CHECK FLOOR WIRE (OPEN)


    1. Using the service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

      A01VJYKE02
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly LH *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire *4 Connector B
      *5 Connector C *6 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      		 *b

      Front view of wire harness connector

      (to No. 2 Side Airbag Sensor Assembly LH)

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-1 (BCL+) - K21-2 (BCL-) Always Below 1 Ω

    NG

    REPLACE FLOOR WIRE

    OK

  8. CHECK FLOOR WIRE (SHORT)


    1. A01VFOFE02
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *4 Connector B
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Disconnect the service wire from connector C.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-1 (BCL+) - K21-2 (BCL-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  9. CHECK FLOOR WIRE (SHORT TO B+)


    1. A01VFOFE02
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *4 Connector B
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K21-1 (BCL+) - Body ground Ignition switch ON Below 1 V
      K21-2 (BCL-) - Body ground Ignition switch ON Below 1 V

    NG

    REPLACE FLOOR WIRE

    OK

  10. CHECK FLOOR WIRE (SHORT TO GROUND)


    1. A01VFOFE02
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly LH
      *3 Floor Wire
      *4 Connector B
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly LH)

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-1 (BCL+) - Body ground Always 1 MΩ or higher
      K21-2 (BCL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  11. CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    1. A01VEVWE01
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly

      Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag sensor assembly.

    2. Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1628/82 is output. A
      DTC B1623/81 is output. B
      DTCs B1623/81 or B1628/82 is not output. C

      Tech Tips

      Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Return the side airbag sensor assembly LH and the side airbag sensor assembly RH to their original positions and connect the connectors to them.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  12. CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH


    1. A01VFE5E16
      Text in Illustration
      *1 No. 2 Side Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly LH

      Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTCs B1623/81 or B1628/82 is not output. A
      DTC B1628/82 is output. B
      DTC B1623/81 is output. C

      Tech Tips

      Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    10. Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    C

    REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH Click here