AIRBAG SYSTEM(w/ VSC), Diagnostic DTC:B1830/57, B1831/57, B1832/57, B1833/57

DTC Code DTC Name
B1830/57 Short in Curtain Shield Squib RH Circuit
B1831/57 Open in Curtain Shield Squib RH Circuit
B1832/57 Short to GND in Curtain Shield Squib RH Circuit
B1833/57 Short to B+ in Curtain Shield Squib RH Circuit

DESCRIPTION

The curtain shield squib RH circuit consists of the airbag sensor assembly and curtain shield airbag assembly RH.

The circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1830/57

  • The airbag sensor assembly receives a line short circuit signal in the curtain shield squib RH circuit during primary check.

  • Curtain shield squib RH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Curtain shield airbag assembly RH (Curtain shield squib RH)

  • Airbag sensor assembly
B1831/57

  • The airbag sensor assembly receives an open circuit signal in the curtain shield squib RH circuit.

  • Curtain shield squib RH malfunction

  • Airbag sensor assembly malfunction
B1832/57

  • The airbag sensor assembly receives a short circuit to ground signal in the curtain shield squib RH circuit.

  • Curtain shield squib RH malfunction

  • Airbag sensor assembly malfunction
B1833/57

  • The airbag sensor assembly receives a short circuit to B+ signal in the curtain shield squib RH circuit.

  • Curtain shield squib RH malfunction

  • Airbag sensor assembly malfunction

WIRING DIAGRAM

A01VGXOE16
*a Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH)
*b Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Tech Tips


  • Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester Click here.

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road Click here.

PROCEDURE


  1. CHECK CONNECTORS


    1. A01VFKNE67
      Text in Illustration
      *1 Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH)
      *2 Airbag Sensor Assembly
      *3 Floor Wire

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the curtain shield airbag assembly RH and airbag sensor assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the curtain shield airbag assembly RH and airbag sensor assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the floor wire connector (on the curtain shield airbag assembly RH side) is not damaged.

      OK
      The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

      OK
      The short spring is not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  2. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)

    SST
    09843-18061

    1. A01VM0ZE02
      Text in Illustration
      *1 Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH)
      *2 Airbag Sensor Assembly
      *3 Connector C
      *a

      Front view of wire harness connector

      (to Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH))

      Connect the connector to the airbag sensor assembly.

    2. Connect SST (resistance 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the curtain shield airbag assembly RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting.

      • Insert SST straight into the terminals of the connector.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      OK
      DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output.

      Tech Tips

      Codes other than DTCs B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.


    OK

    REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH Click here

    NG

  3. CHECK FLOOR WIRE (CURTAIN SHIELD SQUIB CIRCUIT RH)


    1. A01VEI1E02
      Text in Illustration
      *1 Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH)
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH))

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Disconnect SST from connector C.

    4. Disconnect the floor wire from the airbag sensor assembly.

    5. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) battery terminal.

      2. Turn the ignition switch to ON.

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        K28-1 (ICR+) - Body ground Ignition switch ON Below 1 V
        K28-2 (ICR-) - Body ground Ignition switch ON Below 1 V

    6. Check for an open in the circuit.


      1. Turn the ignition switch off.

      2. Disconnect the cable from the negative (-) battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        K28-1 (ICR+) - K28-2 (ICR-) Always Below 1 Ω

    7. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        K28-1 (ICR+) - Body ground Always 1 MΩ or higher
        K28-2 (ICR-) - Body ground Always 1 MΩ or higher

    8. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B Click here.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        K28-1 (ICR+) - K28-2 (ICR-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK DTC


    1. Restore the released activation prevention mechanism of connector B to the original condition.

    2. Connect the connectors to the curtain shield airbag assembly RH and airbag sensor assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      OK
      DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output.

      Tech Tips

      Codes other than DTCs B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.


    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here