ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

PROCEDURE

1. VEHICLE BROUGHT TO WORKSHOP

   Result
   Proceed to NEXT

   
   

   NEXT

2. INSPECT BATTERY VOLTAGE

   Standard Voltage
   11 to 14 V

   If the voltage is below 11 V, recharge or replace the battery before proceeding.

   Tech Tips

   A simple method to determine whether the battery is depleted is to operate the horn.

   Result
   Proceed to NEXT

   
   

   NEXT

3. TURN ENGINE SWITCH ON (IG)

   Tech Tips

   If the engine switch cannot be turned on (IG), communication with the intelligent tester can be confirmed by connecting the intelligent tester to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins.

   Result
   Proceed to NEXT

   
   

   NEXT

4. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

   
   

   1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Click here

      Result
      Result Proceed to CAN DTC is not output A CAN DTC is output B

   
   

   B

   GO TO CAN COMMUNICATION SYSTEM Click here

   A

5. CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

   
   

   1. Use the intelligent tester to check if the LIN communication system is functioning normally.

      Click here

      Result
      Result Proceed to LIN DTC is not output A LIN DTC is output B

   
   

   B

   GO TO LIN COMMUNICATION SYSTEM Click here

   A

6. CHECK FOR DTC (ENTRY AND START SYSTEM)*

   
   

   1. Check for DTCs and make a note of any codes that are output.

   2. Clear the DTCs.

      Click here

   3. Recheck for DTCs. Based on the DTCs output above, try to duplicate the engine immobiliser system DTC or steering lock system DTC by simulating the symptoms indicated by the DTCs.

      Result
      Result Proceed to DTC is not output A Steering lock system DTC is output (DTC B2781, B2782 or B2788) B Engine immobiliser system DTC is output (except DTC B2781, B2782 and B2788) C

   
   

   B

   GO TO STEERING LOCK SYSTEM Click here

   C

   GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

   A

7. CHECK FOR DTC (ECD SYSTEM OR SFI SYSTEM)*

   
   

   1. for 1KR-FE

      
      

      1. Clear the DTCs.

         Click here

      2. Check for DTCs.

         Click here

   2. for 1NR-FE

      
      

      1. Clear the DTCs.

         Click here

      2. Check for DTCs.

         Click here

   3. for 1ND-TV with DPF

      
      

      1. Clear the DTCs.

         Click here

      2. Check for DTCs.

         Click here

   4. for 1ND-TV without DPF

      
      

      1. Clear the DTCs.

         Click here

      2. Check for DTCs.

         Click here

         Tech Tips

         The DTCs for the engine immobiliser system are specified above. If other codes are output, check the DTC chart for the ECD system or SFI system.

      Result
      Result Proceed to DTC is not output A Engine immobiliser system DTC is output (DTC B2799, B279A or B279C) B SFI system DTC is output (for 1KR-FE) C SFI system DTC is output (for 1NR-FE) D ECD system DTC is output (for 1ND-TV with DPF) E ECD system DTC is output (for 1ND-TV without DPF) F

   
   

   B

   GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

   C

   GO TO SFI SYSTEM Click here

   D

   GO TO SFI SYSTEM Click here

   E

   GO TO ECD SYSTEM Click here

   F

   GO TO ECD SYSTEM Click here

   A

8. PROBLEM SYMPTOMS TABLE

   
   

   1. Refer to Problem Symptoms Table.

      Click here

      Result
      Result Proceed to Fault is not listed in problem symptoms table A Fault is listed in problem symptoms table B

   
   

   B

   GO TO STEP 10 Click here

   A

9. OVERALL ANALYSIS AND TROUBLESHOOTING*

   
   

   1. Check Data List / Active Test.

      Click here

   2. Check Terminals of ECU.

      Click here

      Result
      Proceed to NEXT

   
   

   NEXT

10. ADJUST, REPAIR OR REPLACE

    Result
    Proceed to NEXT

    
    

    NEXT

11. CHECK FOR DTC*

    
    

    1. Clear the DTCs.

       Click here

    2. Check for DTCs.

       Click here

       Tech Tips

       Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

       Click here

       Result
       Result Proceed to DTC is not output A Engine immobiliser system DTC is output B

    
    

    A

    END

    B

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here