ENTRY AND START SYSTEM(for Entry Function) Front Passenger Side Door Entry Lock Function does not Operate

DESCRIPTION

If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication between the vehicle and electrical key transmitter sub-assembly is normal. The malfunctioning part may be the lock sensor circuit (from certification ECU (smart key ECU assembly) to the front door outside handle assembly (for front passenger side electrical key antenna)).

WIRING DIAGRAM

A01VHEIE79

CAUTION / NOTICE / HINT

Note


  • When using the intelligent tester with the engine switch off to troubleshoot:

    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

  • The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) Click here.

  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.

  • When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation Click here.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE) Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (P-DOOR TRIGGER SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Entry & Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P-Door Trigger Switch Front door outside handle assembly (for front passenger side) (unlock sensor) / OFF or ON

      OFF: Front door outside handle assembly (for passenger side) (unlock sensor) not touched

      ON: Front door outside handle assembly (for passenger side) (unlock sensor) touched

      • Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

      • Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
      OK
      On the intelligent tester screen, the display changes between ON and OFF as shown in the table above.

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY)


    1. Disconnect the F63 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the G11*1 or H10*2 front door outside handle assembly (for driver side door) connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      F63-11 (CLG2) - G11-6 (ANT1) Always Below 1 Ω
      F63-10 (CG2B) - G11-3 (ANT2) Always Below 1 Ω
      F63-11 (CLG2) - Body ground Always 10 kΩ or higher
      F63-10 (CG2B) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F63-11 (CLG2) - H10-6 (ANT1) Always Below 1 Ω
      F63-10 (CG2B) - H10-3 (ANT2) Always Below 1 Ω
      F63-11 (CLG2) - Body ground Always 10 kΩ or higher
      F63-10 (CG2B) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR)


    1. Reconnect the F63 certification ECU (smart key ECU assembly) connector.

    2. Reconnect the G11*1 or H10*2 front door outside handle assembly connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the voltage according to the value(s) in the table below.

      A01VF7SE01
      Text in Illustration
      *a

      Component with harness connected

      (Certification ECU (smart key ECU assembly))

      		 *b Waveform
      *c Passenger side door lock sensor touched - -
      OK
      Tester Connection Switch Condition Tool Setting Specified Condition
      F63-11 (CLG2) - F65-11 (E)

      Procedure:


      1. Engine switch off

      2. Electrical key transmitter sub-assembly brought outside vehicle

      3. All doors closed

      4. All doors unlocked

      5. Electrical key transmitter sub-assembly brought outside detection area*1

      6. Electrical key transmitter sub-assembly not sufficiently close to vehicle

      7. Front passenger side door lock sensor not touched → touched

      		 2 V/DIV., 500 ms/DIV.

      Pulse generation

      (See waveform)

      • *1: For details about the areas that are outside the entry function detection area, refer to Operation Check Click here.


    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR) Click here