Click here

CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense) Audio Receiver Assembly Communication Stop Mode

Click here
Click here
DTC Code DTC Name
  Audio Receiver Assembly Communication Stop Mode
Click here

DESCRIPTION

Detection Item Symptom Trouble Area
Audio Receiver Assembly Communication Stop Mode

Either condition is met:


  • "Display and Navigation (AVN1)" is not displayed on "Bus Check".

  • "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" applies.

  • Power source or inside radio and display receiver assembly

  • Radio and display receiver assembly branch wire or connector

  • Radio and display receiver assembly
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

  • Turn the ignition switch off before inspecting CAN bus wires for a ground short.

  • After the ignition switch is turned off, check that the key reminder warning system are not operating.

  • Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

Tip:

  • Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

Click here

PROCEDURE


  1. Click here

    CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)


    1. A00470NE02

      Disconnect the radio and display receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      F115-9 (CANH) - F115-10 (CANL) Ignition switch off 54 to 69 Ω
      Table 1. Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

    • OKClick here
    • NG

      REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)

  2. Click here

    CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    1. Disconnect the radio and display receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F113-4 (+B1) - Body ground Always 11 to 14 V
      F115-1 (IG) - Body ground Ignition switch ON 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F113-7 (GND1) - Body ground Always Below 1 Ω
      Table 2. Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)
      Table 3. Result
      Result Proceed to
      OK A
      NG (w/o Stop and Start System) B
      NG (except +B1 circuit) (w/ Stop and Start System)
      NG (for +B1 circuit) (w/ Stop and Start System) C

    • A

      REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

    • B

      REPAIR OR REPLACE HARNESS OR CONNECTOR

    • C

      GO TO STOP AND START SYSTEM (FOR BACKUP BOOST CONVERTER CIRCUIT) (Click here)