NAME PLATE INSTALLATION

PROCEDURE


  1. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE


    1. Clean the attachment surface.


      1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

        Heating Temperature
        Item Temperature
        Vehicle Body 40 to 60°C (104 to 140°F)

        CAUTION:

        Do not burn yourself on the hot body panel or with the infrared light.

        Note

        Do not heat the vehicle body excessively.

      2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

        Note

        Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Install a new No. 2 luggage compartment door name plate as shown in the illustration.

      A01VJSWE01
      Installation Position
      Mark Measurement (along surface)
      *1 223.8 mm (8.81 in.)
      *2 211.9 mm (8.34 in.)
      *3 167.1 mm (6.58 in.)

      Note

      Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.

  2. INSTALL NO. 6 BACK DOOR NAME PLATE


    1. Clean the attachment surface.


      1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

        Heating Temperature
        Item Temperature
        Vehicle Body 40 to 60°C (104 to 140°F)

        CAUTION:

        Do not burn yourself on the hot body panel or with the infrared light.

        Note

        Do not heat the vehicle body excessively.

      2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

        Note

        Installing the No. 6 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. Install a new No. 6 back door name plate as shown in the illustration.

      A01VEOYE05
      Installation Position
      Mark Measurement (along surface)
      *1 215.8 mm (8.50 in.)
      *2 220.0 mm (8.66 in.)
      *3 51.5 mm (2.03 in.)

      Note

      Install the No. 6 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 6 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 6 back door name plate.

  3. INSTALL SYMBOL EMBLEM


    1. Clean the attachment surface.


      1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

        Heating Temperature
        Item Temperature
        Vehicle Body 40 to 60°C (104 to 140°F)

        CAUTION:

        Do not burn yourself on the hot body panel or with the infrared light.

        Note

        Do not heat the vehicle body excessively.

      2. Using a piece of cloth, rub the remaining double-sided tape off the back door panel while it is hot from the infrared light.

        Note

        Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.

    2. A01VLKNE01
      Text in Illustration
      *1 Location Pin

      Insert the 2 pins into the back door panel and install a new symbol emblem.

      Note

      Install the symbol emblem in an environment where the ambient temperature is over 20 °C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.