FRONT DRIVE SHAFT ASSEMBLY(for 2ZR-FE) REASSEMBLY

PROCEDURE


  1. INSTALL FRONT DRIVE SHAFT DUST COVER


    1. B0045BJC08
      *1 Press

      Using SST and a press, install a new front drive shaft dust cover into the front drive inboard joint assembly until it is flush with the end.

      SST
      09527-10011

      Note


      • Install the front drive shaft dust cover in the correct orientation.

      • Do not deform the front drive shaft dust cover.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  2. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING


    1. Install a new front drive shaft hole snap ring.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT

    B0046IMC17
    *1 Protective Tape

    1. Wrap the spline of the outboard joint shaft assembly with protective tape.

    2. Install new parts onto the outboard joint shaft assembly in the following order.


      1. Front No. 2 axle outboard joint boot clamp

      2. Front axle outboard joint boot

      3. Front axle outboard joint boot clamp

    3. Pack the joint portion of the outboard joint shaft assembly and the front axle outboard joint boot with grease.

      Standard Grease Capacity
      151 to 161 g (5.33 to 5.68 oz.)

    4. Install the front axle outboard joint boot onto the outboard joint shaft assembly groove.

      Note

      Keep the groove free of grease.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  4. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP


    1. Hold the outboard joint shaft assembly in a vise between aluminum plates.

    2. Install a new front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot.

    3. B0047O9E01

      Place SST onto the front No. 2 axle outboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. B004821E07

      Using SST, adjust the clearance of the front No. 2 axle outboard joint boot clamp.

      SST
      09240-00021
      Standard Clearance
      0.8 mm (0.0315 in.) or less

      Note

      If the measured value exceeds the specified value, retighten the front No. 2 axle outboard joint boot clamp.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP


    1. Hold the outboard joint shaft assembly in a vise between aluminum plates.

    2. Install a new front axle outboard joint boot clamp to the front axle outboard joint boot.

    3. B0045SME06

      Place SST onto the front axle outboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the front axle outboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. B00460PE04

      Using SST, adjust the clearance of the front axle outboard joint boot clamp.

      SST
      09240-00021
      Standard Clearance
      0.8 mm (0.0315 in.) or less

      Note

      If the measured value exceeds the specified value, retighten the front axle outboard joint boot clamp.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  6. INSTALL FRONT DRIVE SHAFT DAMPER RH


    1. B0045N3C01
      *1 Front Drive Outboard Joint Shaft Assembly RH
      *2 Front Drive Shaft Damper RH
      *3 Front Drive Shaft Damper Clamp

      Install parts to the front drive outboard joint shaft assembly RH in the following order as shown in the illustration.


      1. Front drive shaft damper RH

        Note

        Install the front drive shaft damper in the correct orientation.

      2. New front drive shaft damper clamp

    2. Secure the front drive outboard joint shaft assembly RH in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    3. Install the front drive shaft damper clamp to the front drive shaft damper RH.

      Note

      Be sure to install the clamp in the correct position.

    4. Set the dimension (A) as specified below.

      Dimension (A)
      449 to 453 mm (1.47 to 1.49 ft.)

    5. Fix the front drive shaft damper RH.


      1. B0046FMC01
        *a Hold
        *b Turn

        Place SST onto the front drive shaft damper clamp, press it against the front drive shaft damper RH and slightly tighten SST.

        SST
        09521-24010

      2. Remove SST.

      3. B00472IE01

        Using SST, measure the clearance of the front drive shaft damper clamp.

        SST
        09240-00021
        Standard Clearance
        0.8 mm (0.0315 in.) or less

        Note

        If the measured value exceeds the specified value, retighten the front drive shaft damper clamp.

  7. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY


    1. Install new parts onto the outboard joint shaft assembly in the following order.


      1. Front axle inboard joint boot clamp

      2. Front axle inboard joint boot

      3. Front No. 2 axle inboard joint boot clamp

    2. Fix the outboard joint shaft assembly in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    3. Remove the protective tape.

    4. B0046RCC01
      *a Matchmark

      Align the matchmarks and install the tripod joint assembly onto the outboard joint shaft assembly.

      Note

      Face the serrated side of the tripod joint assembly outward and install it onto the outboard joint shaft assembly end.

    5. Using a brass bar and hammer, install the tripod joint assembly.

      Note


      • Do not hit the rollers.

      • Keep the tripod joint assembly free of foreign matter.

    6. B0047T5

      Using a snap ring expander, install a new snap ring.

    7. Pack the inboard joint with grease.

      Standard Grease Capacity
      125 to 135 g (4.41 to 4.76 oz.)
    8. B0046M7C23
      *a Matchmark

      Align the matchmarks and install the front drive inboard joint assembly onto the outboard joint shaft assembly.

    9. Install the front axle inboard joint boot into the grooves of the front drive inboard joint assembly and outboard joint shaft assembly.

      Note

      Keep the grooves free of grease.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  8. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP


    1. Hold the outboard joint shaft assembly in a vise between aluminum plates.

    2. Install a new front axle inboard joint boot clamp to the front axle inboard joint boot.

    3. B0046PBE01

      Place SST onto the front axle inboard joint boot clamp.

      SST
      09521-24010

    4. Tighten SST so that the front axle inboard joint boot clamp is pinched.

      Note

      Do not overtighten SST.

    5. B0047YUE01

      Using SST, adjust the clearance of the front axle inboard joint boot clamp.

      SST
      09240-00021
      Standard Clearance
      0.8 mm (0.0315 in.) or less

      Note

      If the measured value exceeds the specified value, retighten the front axle inboard joint boot clamp.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  9. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP


    1. Install a new front No. 2 inboard joint boot clamp onto the front axle inboard joint boot.

    2. B0045Q7E01

      Adjust dimension (A) until the drive shaft is within the specified length.

      Dimension (A)
      LH Side RH Side
      543.1 mm (1.78 ft.) 821 mm (2.69 ft.)
    3. B0045KZ

      Using needle-nose pliers, engage the 2 claws and install the front No. 2 inboard joint boot clamp as shown in the illustration.

      Note


      • Do not damage the front axle inboard joint boot.

      • Do not deform the claw of the hook.

      Tech Tips

      Use the same procedure for the RH side as for the LH side.

  10. INSPECT FRONT DRIVE SHAFT ASSEMBLY

    Click here