TRANSMISSION CONTROL CABLE ADJUSTMENT

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  4. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

    Click here

  5. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  6. REMOVE AIR CLEANER BRACKET

    Click here

  7. REMOVE BATTERY

    Click here

  8. REMOVE BATTERY TRAY

    Click here

  9. REMOVE BATTERY CARRIER (for LHD)

    Click here

  10. REMOVE BATTERY CARRIER (for RHD)

    Click here

  11. REMOVE NO. 1 AIR TUBE

    Click here

  12. REMOVE REAR CONSOLE BOX

    Click here

  13. ADJUST TRANSMISSION CONTROL SELECT CABLE


    1. A01VHS4

      Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.

    2. A01VKHRE02
      Text in Illustration
      *1 Case
      *2 Lock Piece
      *3 Slider
      *a Before lock release
      *b After lock release
      A01VL3H Slide
      A01VE7C Push out

      Release the lock of the cable length adjustment structure of the transmission control select cable.


      1. Slide the slider.

      2. Push the lock piece downward to release the lock.

    3. A01VK6CE04
      Text in Illustration
      *1 Reverse Restrict Pin Assembly
      *2 Outer Select Lever

      Hook the outer select lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.

    4. A01VLVAE02
      Text in Illustration
      *1 Slider Shaft
      *2 Cam Wall
      *3 Lock Piece
      *4 Slider
      A01VL3H Push
      A01VE7C Push in

      Connect the transmission control select cable to the floor shift shift lever assembly with the clip.

      Note

      Make sure that the lock piece protrudes from the adjuster case.

    5. Push the slider shaft until it contacts the cam wall.

      Note


      • Do not pull up the slider shaft.

      • When adjusting the cable, make sure that the shift lever is in neutral between the 1st and 2nd gear positions.

    6. Lock the cable length adjustment structure of the transmission control select cable.

      Note


      • Push the lock piece as far as it will go.

      • Confirm whether the cable length adjustment structure is locked securely.

    7. A01VH5LE02
      Text in Illustration
      *1 Reverse Restrict Pin Assembly
      *2 Outer Select Lever
      *a Release

      Move the shift lever to the reverse position, so that the outer select lever can be released.

  14. INSTALL REAR CONSOLE BOX

    Click here

  15. INSTALL NO. 1 AIR TUBE

    Click here

  16. INSTALL BATTERY CARRIER (for LHD)

    Click here

  17. INSTALL BATTERY CARRIER (for RHD)

    Click here

  18. INSTALL BATTERY TRAY

    Click here

  19. INSTALL BATTERY

    Click here

  20. INSTALL AIR CLEANER BRACKET

    Click here

  21. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  22. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

    Click here

  23. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }