MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
| *A | for 2NR-FKE | *B | w/o Neutral Position Switch |
| *C | w/ Neutral Position Switch | - | - |
| *1 | BACK-UP LIGHT SWITCH ASSEMBLY | *2 | BLEEDER CLUTCH RELEASE TUBE |
| *3 | BREATHER PLUG | *4 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
| *5 | CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY | *6 | CONTROL CABLE BRACKET ASSEMBLY |
| *7 | MANUAL TRANSMISSION DRAIN PLUG | *8 | MANUAL TRANSMISSION FILLER PLUG |
| *9 | NO. 1 CLUTCH HOUSING COVER | *10 | RELEASE CYLINDER BLEEDER PLUG |
| *11 | RELEASE CYLINDER BLEEDER PLUG CAP | *12 | NEUTRAL POSITION SWITCH |
| *13 | CLUTCH TUBE BOOT | *14 | GASKET |
| *15 | TRANSMISSION CASE PLUG | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |
| ● | Non-reusable part |  |
Clutch spline grease |
ILLUSTRATION
| *A | for 2ZR-FE | - | - |
| *1 | BACK-UP LIGHT SWITCH ASSEMBLY | *2 | BLEEDER CLUTCH RELEASE TUBE |
| *3 | BREATHER PLUG | *4 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
| *5 | CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY | *6 | CONTROL CABLE BRACKET ASSEMBLY |
| *7 | MANUAL TRANSMISSION DRAIN PLUG | *8 | MANUAL TRANSMISSION FILLER PLUG |
| *9 | NO. 1 CLUTCH HOUSING COVER | *10 | RELEASE CYLINDER BLEEDER PLUG |
| *11 | RELEASE CYLINDER BLEEDER PLUG CAP | *12 | CLUTCH TUBE BOOT |
| *13 | GASKET | *14 | TRANSMISSION CASE PLUG |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | * | For use with union nut wrench |
| ● | Non-reusable part | |
Clutch spline grease |
ILLUSTRATION
| *A | for 2NR-FKE | - | - |
| *1 | STRAIGHT PIN | *2 | SHIFT AND SELECT LEVER SHAFT STRAIGHT SCREW WITH HEAD PLUG |
| *3 | SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING | *4 | LOCK BALL PIN |
| *5 | TRANSMISSION CASE PLUG | *6 | REVERSE IDLER GEAR SHAFT BOLT |
| *7 | SHIFT DETENT BALL | *8 | SHIFT DETENT BALL COMPRESSION SPRING |
| *9 | SHIFT DETENT BALL PLUG | *10 | NO. 1 LOCK BALL ASSEMBLY |
| *11 | OUTER SHIFT LEVER E RING | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for 2ZR-FE | - | - |
| *1 | STRAIGHT PIN | *2 | SHIFT AND SELECT LEVER SHAFT STRAIGHT SCREW WITH HEAD PLUG |
| *3 | SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING | *4 | LOCK BALL PIN |
| *5 | TRANSMISSION CASE PLUG | *6 | REVERSE IDLER GEAR SHAFT BOLT |
| *7 | SHIFT DETENT BALL | *8 | SHIFT DETENT BALL COMPRESSION SPRING |
| *9 | SHIFT DETENT BALL PLUG | *10 | NO. 1 LOCK BALL ASSEMBLY |
| *11 | OUTER SHIFT LEVER E RING | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for 2NR-FKE | - | - |
| *1 | OUTER SELECT LEVER | *2 | OUTER SELECT LEVER OIL SEAL |
| *3 | INNER SELECT LEVER | *4 | INNER SELECT LEVER SET BOLT |
| *5 | REVERSE SHIFT ARM BRACKET ASSEMBLY | *6 | REVERSE SHIFT FORK SHAFT ASSEMBLY |
| *7 | REVERSE IDLER GEAR SUB-ASSEMBLY | *8 | REVERSE IDLER THRUST WASHER |
| *9 | REVERSE IDLER GEAR SHAFT | *10 | INPUT SHAFT ASSEMBLY |
| *11 | NO. 3 GEAR SHIFT FORK SHAFT ASSEMBLY | *12 | NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY |
| *13 | NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY | *14 | OUTPUT SHAFT ASSEMBLY |
| *15 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE) | *16 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE) |
| *17 | SHIFT AND SELECT LEVER SHAFT ASSEMBLY | *18 | SHIFT INTER LOCK PLATE |
| *19 | DIFFERENTIAL CASE ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for 2ZR-FE | - | - |
| *1 | OUTER SELECT LEVER | *2 | OUTER SELECT LEVER OIL SEAL |
| *3 | INNER SELECT LEVER | *4 | INNER SELECT LEVER SET BOLT |
| *5 | REVERSE SHIFT ARM BRACKET ASSEMBLY | *6 | REVERSE SHIFT FORK SHAFT ASSEMBLY |
| *7 | REVERSE IDLER GEAR SUB-ASSEMBLY | *8 | REVERSE IDLER THRUST WASHER |
| *9 | REVERSE IDLER GEAR SHAFT | *10 | INPUT SHAFT ASSEMBLY |
| *11 | NO. 3 GEAR SHIFT FORK SHAFT ASSEMBLY | *12 | NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY |
| *13 | NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY | *14 | OUTPUT SHAFT ASSEMBLY |
| *15 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE) | *16 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE) |
| *17 | SHIFT AND SELECT LEVER SHAFT ASSEMBLY | *18 | SHIFT INTER LOCK PLATE |
| *19 | DIFFERENTIAL CASE ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for 2NR-FKE | - | - |
| *1 | REVERSE RESTRICT PIN ASSEMBLY | *2 | TRANSMISSION CASE OIL SEAL (for RH SIDE) |
| *3 | FRONT TRANSAXLE CASE OIL SEAL | *4 | TRANSMISSION MAGNET |
| *5 | OUTPUT SHAFT COVER | *6 | FRONT OUTPUT SHAFT BEARING (OUTER RACE) |
| *7 | FRONT DIFFERENTIAL CASE FRONT PLATE WASHER | *8 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) |
| *9 | FRONT TRANSAXLE CASE | *10 | TRANSMISSION OIL SEPARATOR |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP Grease | - | - |
ILLUSTRATION
| *A | for 2ZR-FE | - | - |
| *1 | REVERSE RESTRICT PIN ASSEMBLY | *2 | TRANSMISSION CASE OIL SEAL (for RH SIDE) |
| *3 | FRONT TRANSAXLE CASE OIL SEAL | *4 | TRANSMISSION MAGNET |
| *5 | OUTPUT SHAFT COVER | *6 | FRONT OUTPUT SHAFT BEARING (OUTER RACE) |
| *7 | FRONT DIFFERENTIAL CASE FRONT PLATE WASHER | *8 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) |
| *9 | FRONT TRANSAXLE CASE | *10 | TRANSMISSION OIL SEPARATOR |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP Grease | - | - |
ILLUSTRATION
| *A | for 2NR-FKE | - | - |
| *1 | TRANSMISSION OIL SEPARATOR | *2 | NO. 1 OIL RECEIVER PIPE |
| *3 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) | *4 | REAR INPUT SHAFT BEARING SHIM |
| *5 | INPUT SHAFT COVER | *6 | REAR OUTPUT SHAFT BEARING (OUTER RACE) |
| *7 | REAR OUTPUT SHAFT BEARING SHIM | *8 | MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY |
| *9 | TRANSMISSION CASE OIL SEAL (for LH SIDE) | *10 | MANUAL TRANSMISSION CASE |
| *11 | FRONT DIFFERENTIAL CASE REAR PLATE WASHER | *12 | OUTER SHIFT LEVER OIL SEAL |
| *13 | OUTER SHIFT LEVER SPACER | *14 | OUTER NO. 1 SHIFT LEVER |
| *15 | INNER NO. 1 SHIFT LEVER | *16 | INNER SHIFT LEVER SLOTTED SPRING PIN |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP Grease | - | - |
ILLUSTRATION
| *A | for 2ZR-FE | - | - |
| *1 | TRANSMISSION OIL SEPARATOR | *2 | NO. 1 OIL RECEIVER PIPE |
| *3 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) | *4 | REAR INPUT SHAFT BEARING SHIM |
| *5 | INPUT SHAFT COVER | *6 | REAR OUTPUT SHAFT BEARING (OUTER RACE) |
| *7 | REAR OUTPUT SHAFT BEARING SHIM | *8 | MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY |
| *9 | TRANSMISSION CASE OIL SEAL (for LH SIDE) | *10 | MANUAL TRANSMISSION CASE |
| *11 | FRONT DIFFERENTIAL CASE REAR PLATE WASHER | *12 | OUTER SHIFT LEVER OIL SEAL |
| *13 | OUTER SHIFT LEVER SPACER | *14 | OUTER NO. 1 SHIFT LEVER |
| *15 | INNER NO. 1 SHIFT LEVER | *16 | INNER SHIFT LEVER SLOTTED SPRING PIN |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP Grease | - | - |