TRANSMISSION CONTROL CABLE(for TMMF Made) ADJUSTMENT

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. DISCONNECT NO. 2 VENTILATION HOSE (for 2ZR-FE)

    Click here

  4. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE (for 2ZR-FE)

    Click here

  5. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for 2ZR-FE)

    Click here

  6. REMOVE AIR CLEANER CASE SUB-ASSEMBLY (for 2ZR-FE)

    Click here

  7. REMOVE BATTERY

    Click here

  8. REMOVE BATTERY TRAY

    Click here

  9. REMOVE BATTERY CARRIER

    Click here

  10. REMOVE REAR CONSOLE BOX

    Click here

  11. ADJUST TRANSMISSION CONTROL SELECT CABLE


    1. B0045AX

      Remove the clip and disconnect the transmission control select cable from the shift lever.

    2. B004778C02
      *1 Case
      *2 Lock Piece
      *3 Slider
      *a Before lock release
      *b After lock release
      B0046MU Slide
      B0045SR Push out

      Release the lock of the cable length adjustment structure of the transmission control select cable.


      1. Slide the slider.

      2. Push the lock piece downward to release the lock.

    3. B00473ME04
      Text in Illustration
      *1 Reverse Restrict Pin Assembly
      *2 Outer Select Lever

      Hook the outer select lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.

    4. B0045GDE02
      Text in Illustration
      *1 Slider Shaft
      *2 Cam Wall
      *3 Lock Piece
      *4 Slider
      B0046MU Push
      B0045SR Push in

      Connect the transmission control select cable to the floor shift shift lever assembly with the clip.

      Note

      Make sure that the lock piece protrudes from the adjuster case.

    5. Push the slider shaft until it contacts the cam wall.

      Note


      • Do not pull up the slider shaft.

      • When adjusting the cable, make sure that the shift lever is in neutral between the 1st and 2nd gear positions.

    6. Lock the cable length adjustment structure of the transmission control select cable.

      Note


      • Push the lock piece as far as it will go.

      • Confirm whether the cable length adjustment structure is locked securely.

    7. B0046K0E02
      Text in Illustration
      *1 Reverse Restrict Pin Assembly
      *2 Outer Select Lever
      *a Release

      Move the shift lever to the reverse position, so that the outer select lever can be released.

  12. INSTALL REAR CONSOLE BOX

    Click here

  13. INSTALL BATTERY CARRIER

    Click here

  14. INSTALL BATTERY TRAY

    Click here

  15. INSTALL BATTERY

    Click here

  16. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2ZR-FE)

    Click here

  17. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for 2ZR-FE)

    Click here

  18. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE (for 2ZR-FE)

    Click here

  19. CONNECT NO. 2 VENTILATION HOSE (for 2ZR-FE)

    Click here

  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here