STOP AND START SYSTEM Neutral Position Switch Circuit

DESCRIPTION

The neutral position switch detects whether the shift lever is in neutral. While the neutral position switch is off, engine restart operation due to stop and start system control is prohibited.

WIRING DIAGRAM

A0047DTE04

PROCEDURE


  1. READ VALUE USING GTS (NEUTRAL SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

    5. Read the value when the shift lever is in neutral and any other position.

      OK
      ON is displayed when the shift lever is in neutral.
      OFF is displayed when the shift lever is in any other position.

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SWITCH)


    1. Disconnect the B96 neutral position switch connector. (for 2NR-FKE, 1ND-TV)

    2. Disconnect the A100 neutral position switch connector. (for 1KR-FE)

    3. Disconnect the A92 engine stop and start ECU connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 2NR-FKE, 1ND-TV
      Tester Connection Condition Specified Condition
      A92-26 (TMVC) - B96-1 (W1) Always Below 1 Ω
      A92-27 (TMN) - B96-2 (TMN) Always Below 1 Ω
      A92-25 (TME2) - B96-3 (F+) Always Below 1 Ω
      A92-26 (TMVC) or B96-1 (W1) - Body ground Always 10 kΩ or higher
      A92-27 (TMN) or B96-2 (TMN) - Body ground Always 10 kΩ or higher
      A92-25 (TME2) or B96-3 (F+) - Body ground Always 10 kΩ or higher
      for 1KR-FE
      Tester Connection Condition Specified Condition
      A92-26 (TMVC) - A100-1 (W1) Always Below 1 Ω
      A92-27 (TMN) - A100-2 (TMN) Always Below 1 Ω
      A92-25 (TME2) - A100-3 (F+) Always Below 1 Ω
      A92-26 (TMVC) or A100-1 (W1) - Body ground Always 10 kΩ or higher
      A92-27 (TMN) or A100-2 (TMN) - Body ground Always 10 kΩ or higher
      A92-25 (TME2) or A100-3 (F+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK NEUTRAL POSITION SWITCH (TMN TERMINAL VOLTAGE)


    1. Measure the voltage according to the value(s) in the table below.

      A004A2YE01
      Text in Illustration
      *a

      Component with harness connected

      (Engine Stop and Start ECU)

      		 - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      A92-27 (TMN) - A92-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
      Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V
      Result
      Result Proceed to
      OK A
      NG (for 2NR-FKE) B
      NG (for 1KR-FE) C
      NG (for 1ND-TV) D

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    B

    REPLACE NEUTRAL POSITION SWITCH Click here

    C

    REPLACE NEUTRAL POSITION SWITCH Click here

    D

    REPLACE NEUTRAL POSITION SWITCH Click here