P0560

DTC Code	DTC Name
P0560	System Voltage

DESCRIPTION

The engine stop and start ECU detects malfunctions based on +B terminal voltage and VB voltage characteristics when the VB- circuit is open. If the VB- circuit is open, the engine stop and start ECU stores DTC P0560 and blinks the stop and start cancel indicator light.

DTC No.	DTC Detection Condition	Trouble Area
P0560	VB voltage is below the threshold of the VB circuit open judgment voltage for 1 second or more (1 trip detection logic).	Wire harness or connector Engine stop and start ECU

CONFIRMATION DRIVING PATTERN

After troubleshooting, perform the following steps to recheck for DTCs.
Tech Tips
- If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. After connecting the cable, drive the vehicle until refresh charge is completed and stop and start control is permitted (approximately 15 to 40 minutes).
- Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
1. for Manual transaxle
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs Click here.
  4. Start the engine and warm it up.
  5. Drive the vehicle at 7 km/h (4.3 mph) or more.
    
    CAUTION:
    
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  6. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
  7. Keep the engine stopped by stop and start control for 1 second or more.
  8. Depress the clutch pedal and start the engine.
    
    Tech Tips
    
    If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.
  9. Check that DTCs are not output Click here.
2. for CVT
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs Click here.
  4. Start the engine and warm it up.
  5. Drive the vehicle at 7 km/h (4.3 mph) or more.
    
    CAUTION:
    
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  6. Depress the brake pedal and stop the vehicle.
  7. Keep the engine stopped by stop and start control for 1 second or more (Keep the shift lever in D).
  8. Release the brake pedal with the shift lever in D to start the engine.
    
    Tech Tips
    
    If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.
  9. Check that DTCs are not output Click here.
Check if the stop and start system operates normally.

Tech Tips

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. After connecting the cable, drive the vehicle until refresh charge is completed and stop and start control is permitted (approximately 15 to 40 minutes).
1. for Manual transaxle
  1. Start the engine and warm it up.
  2. Turn the air conditioning system off.
  3. Drive the vehicle at 7 km/h (4.3 mph) or more.
    
    CAUTION:
    
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  4. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
  5. Allow the engine to stop by stop and start control.
  6. Depress the clutch pedal and start the engine.
2. for CVT
  1. Start the engine and warm it up.
  2. Turn the air conditioning system off.
  3. Drive the vehicle at 7 km/h (4.3 mph) or more.
    
    CAUTION:
    
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.
  4. Depress the brake pedal and stop the vehicle.
  5. Keep the engine stopped by stop and start control for 1 second or more (Keep the shift lever in D).
  6. Release the brake pedal with the shift lever in D to start the engine.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

Note

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU Click here.
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU Click here.
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU Click here.
Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting Click here.

PROCEDURE

CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN RELAY)

Text in Illustration

*a
Front view of wire harness connector

(to Engine Stop and Start ECU)

Disconnect the engine stop and start ECU connector.
Turn the ignition switch to ON.

Text in Illustration
*a	Front view of wire harness connector (to Engine Stop and Start ECU)

Measure the voltage according to the value(s) in the table below.

Standard Voltage

Tester Connection	Switch Condition	Specified Condition
A91-5 (+B) - A91-8 (GND)	Ignition switch ON	9.5 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

Disconnect the A92 engine stop and start ECU connector.

Measure the resistance according to the value(s) in the table below.

Standard Resistance

Tester Connection	Condition	Specified Condition
A92-17 (VB-) - Body ground	Always	Below 1 Ω

OK

INSPECT ENGINE STOP AND START ECU Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

STOP AND START SYSTEM, Diagnostic DTC:P0560