STOP AND START SYSTEM, Diagnostic DTC:P0562

DTC Code DTC Name
P0562 System Voltage Low

DESCRIPTION

The engine stop and start ECU monitors +B terminal voltage while the engine is stopped by stop and start control. If the voltage drops below the specified level, the engine stop and start ECU stores DTC P0562 and blinks the stop and start cancel indicator light.

DTC No. DTC Detection Condition Trouble Area
P0562

All of the following conditions are met for 2 seconds or more (1 trip detection logic):


  • +B terminal voltage is 9 V or less.

  • Engine stopped by stop and start control.

  • Battery

  • Wire harness or connector

  • No. 1 integration relay

  • Engine stop and start ECU

CONFIRMATION DRIVING PATTERN

Tech Tips

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs Click here.


  1. After troubleshooting, perform the following steps to recheck for DTCs.

    Tech Tips


    • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

      In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

    • If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates. If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

    • After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

    • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.


    1. for Manual Transaxle


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON and turn the GTS on.

      3. Clear the DTCs Click here.

      4. Start the engine and warm it up.

      5. Drive the vehicle at 7 km/h (4.3 mph) or more.

        CAUTION:

        When performing the confirmation driving pattern, obey all speed limits and traffic laws.

      6. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

      7. Keep the engine stopped by stop and start control for 1 second or more.

      8. Depress the clutch pedal and start the engine.

        Tech Tips

        If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.

      9. Check that DTCs are not output Click here.

    2. for CVT


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON and turn the GTS on.

      3. Clear the DTCs Click here.

      4. Start the engine and warm it up.

      5. Drive the vehicle at 7 km/h (4.3 mph) or more.

        CAUTION:

        When performing the confirmation driving pattern, obey all speed limits and traffic laws.

      6. Depress the brake pedal and stop the vehicle.

      7. Keep the engine stopped by stop and start control for 1 second or more (Keep the shift lever in D).

      8. Release the brake pedal with the shift lever in D to start the engine.

        Tech Tips

        If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.

      9. Check that DTCs are not output Click here.

  2. Check if the stop and start system operates normally.

    Tech Tips


    • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

      In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

    • If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates. If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

    • After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.


    1. for Manual Transaxle


      1. Start the engine and warm it up.

      2. Turn the air conditioning system off.

      3. Drive the vehicle at 7 km/h (4.3 mph) or more.

        CAUTION:

        When performing the confirmation driving pattern, obey all speed limits and traffic laws.

      4. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

      5. Allow the engine to stop by stop and start control.

      6. Depress the clutch pedal and start the engine.

    2. for CVT


      1. Start the engine and warm it up.

      2. Turn the air conditioning system off.

      3. Drive the vehicle at 7 km/h (4.3 mph) or more.

        CAUTION:

        When performing the confirmation driving pattern, obey all speed limits and traffic laws.

      4. Depress the brake pedal and stop the vehicle.

      5. Keep the engine stopped by stop and start control for 1 second or more (Keep the shift lever in D).

      6. Release the brake pedal with the shift lever in D to start the engine.

WIRING DIAGRAM

A0048X1E04
A0048X1E02
A0048X1E05

CAUTION / NOTICE / HINT

Note


  • Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU Click here.

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU Click here.

  • After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting Click here.

PROCEDURE


  1. READ VALUE USING GTS (BATTERY VOLTAGE)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

      Tech Tips

      Do not start the engine.

    3. Turn the GTS on.

    4. Turn off all electrical systems.

    5. Enter the following menus: Powertrain / Stop and Start / Data List / Battery Voltage.

    6. Read the battery voltage displayed on the GTS screen.

      Result
      Result Proceed to
      Below 9 V A
      9 to 14 V (for 2NR-FKE) B
      9 to 14 V (for 1KR-FE) C
      9 to 14 V (for 1ND-TV) D

    B

    CHECK BATTERY AND CHARGING SYSTEM Click here

    C

    CHECK BATTERY AND CHARGING SYSTEM Click here

    D

    CHECK BATTERY AND CHARGING SYSTEM Click here

    A

  2. INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)


    1. Inspect the No. 1 integration relay (for 2NR-FKE) Click here.

    2. Inspect the No. 1 integration relay (for 1KR-FE) Click here.

    3. Inspect the No. 1 integration relay (for 1ND-TV) Click here.

      Result
      Result Proceed to
      OK A
      NG (for 2NR-FKE) B
      NG (for 1KR-FE) C
      NG (for 1ND-TV) D

    B

    REPLACE NO. 1 INTEGRATION RELAY Click here

    C

    REPLACE NO. 1 INTEGRATION RELAY Click here

    D

    REPLACE NO. 1 INTEGRATION RELAY Click here

    A

  3. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)


    1. Remove the No. 1 integration relay from the engine room main relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1E-10 - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ENGINE STOP AND START ECU)


    1. Disconnect the A91 engine stop and start ECU connector.

    2. Remove the No. 1 integration relay from the engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1D-22*1 or 1D-10*2 - A91-5 (+B) Always Below 1 Ω
      A91-5 (+B) or 1D-22*1 - Body ground Always 10 kΩ or higher
      A91-5 (+B) or 1D-10*2 - Body ground Always 10 kΩ or higher

      *1: 2NR-FKE, 1KR-FE

      *2: 1ND-TV


    OK

    REPLACE ENGINE STOP AND START ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR