OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

  • In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.

    2. Remove the oil pan drain plug and oil pan drain plug gasket from the oil pan sub-assembly, and drain the engine oil into a container.

    3. Clean and install the oil pan drain plug with a new oil pan drain plug gasket to the oil pan sub-assembly.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }

  2. REMOVE OIL FILTER CAP ASSEMBLY


    1. A004BC2C28
      *a Pipe
      *b Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A00498H

      Remove the oil filter drain plug from the oil filter cap assembly.

    3. A00494WC04
      *1 Oil Filter Cap Assembly
      *2 Oil Filter Drain Plug O-ring
      *a Pipe
      *b Hose

      Insert the pipe with hose into the oil filter cap assembly.

      Note

      Be sure to insert the pipe with the oil filter drain plug O-ring installed to the oil filter cap assembly.

      Tech Tips

      Place the hose end into a container before draining the engine oil from the hose.

    4. A004AZ2

      Make sure that the engine oil is completely drained, and remove the pipe with hose and oil filter drain plug O-ring.

      Tech Tips

      Pull the pipe with hose as shown in the illustration to remove it.

    5. A0047AWE01

      Using SST, remove the oil filter cap assembly from the oil pan sub-assembly.

      SST
      09228-06502
    6. A004BFTC24
      *1 Oil Filter Element
      *2 Oil Filter Cap Gasket

      Remove the oil filter element and oil filter cap gasket from the oil filter cap assembly.

      Note

      Do not use any tools to remove the oil filter cap gasket in order to prevent the oil filter cap assembly from being damaged. Be sure to remove it by hand.

  3. INSTALL OIL FILTER CAP ASSEMBLY


    1. Clean the inside of the oil filter cap assembly, the threads and oil filter cap gasket groove.

    2. A0049XQC06
      *1 Oil Filter Cap Gasket
      *a Correct
      *b Incorrect

      Apply a small amount of engine oil to a new oil filter cap gasket and install it to the oil filter cap assembly.

      Note


      • Be sure to install the oil filter cap gasket in the proper location, otherwise engine oil may leak.

      • Do not twist the oil filter cap gasket.

    3. Set a new oil filter element in the oil filter cap assembly.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the oil filter cap gasket again and temporarily install the oil filter cap assembly to the oil pan sub-assembly.

      Note

      Make sure that the oil filter cap gasket does not get caught between the parts.

    6. A0046ZRC04
      *1 Oil Filter Cap Assembly
      *2 Oil Filter Cap Gasket
      *3 Oil Pan Sub-assembly
      *a No Gap

      Using SST, tighten the oil filter cap assembly.

      SST
      09228-06502
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note


      • After tightening the oil filter cap assembly, make sure that there is no gap and that the oil filter cap gasket is not protruding.

      • Do not cross thread the oil filter cap assembly.

    7. Apply a small amount of engine oil to a new oil filter drain plug O-ring and install it to the oil filter cap assembly.

      Note

      Remove any dirt or foreign matter from the installation surface.

    8. A0047FIC02
      *1 Oil Filter Drain Plug O-ring

      Install the oil filter drain plug to the oil filter cap assembly.

      Torque:
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Make sure that the oil filter drain plug O-ring does not get caught between the parts.

  4. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil

      • 0W-20

      • 5W-30

      • 10W-30
      API grade SL, SM or SN multigrade engine oil

      • 15W-40
      Standard Oil Capacity
      Item Specified Condition
      Drain and refill with oil filter change 3.6 liters (3.8 US qts, 3.2 Imp. qts)
      Drain and refill without oil filter change 3.4 liters (3.6 US qts, 3.0 Imp. qts)
      Dry fill 4.1 liters (4.3 US qts, 3.6 Imp. qts)

    2. Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.

  5. CHECK ENGINE OIL LEVEL

    Click here

  6. INSPECT FOR ENGINE OIL LEAK


    1. Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.