OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. Skin should be washed with soap and water, or use waterless hand cleaner, to thoroughly remove any used engine oil. Do not use gasoline, thinners, or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.

    2. Remove the oil pan drain plug and the gasket from the oil pan sub-assembly, and drain the engine oil into a container.

    3. Clean and install the oil pan drain plug with a new gasket to the oil pan sub-assembly.

      Torque:
      30 N*m  { 301 kgf*cm, 22 ft.*lbf }

  2. REMOVE OIL FILTER ELEMENT


    1. A01VFSYE02
      Text in Illustration
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A01VE7I

      Remove the oil filter drain plug from the oil filter cap.

    3. A01VJJ1E07
      Text in Illustration
      *1 Oil Filter Cap
      *2 Valve
      *3 Pipe
      *4 Drain Plug O-ring
      *5 Hose

      Insert the pipe with the hose into the oil filter cap.

      Note

      Be sure to insert the pipe with the drain plug O-ring installed on the oil filter cap.

      Tech Tips

      Place the hose end into a container before draining the engine oil.

    4. A01VFOU

      Make sure that the engine oil has been completely drained, and remove the pipe with the hose and drain plug O-ring.

      Tech Tips

      Be sure to turn the pipe in the direction of the arrow to remove it.

    5. A01VKULE03

      Using SST, remove the oil filter cap from the oil pan sub-assembly.

      SST
      09228-06501
    6. A01VH3XE02
      Text in Illustration
      *1 Oil Filter Element
      *2 O-ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Do not use any tools to remove the O-ring to prevent damage to the oil filter cap. Be sure to remove it by hand.

  3. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, the threads and the O-ring groove.

    2. A01VEBEE03
      Text in Illustration
      *1 O-ring
      *a Correct
      *b Incorrect

      Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise engine oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element to the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the oil pan sub-assembly.

    5. Apply a small amount of engine oil to the O-ring again and temporarily tighten the oil filter cap to the oil pan sub-assembly.

    6. A01VDRJE02
      Text in Illustration
      *1 Oil Pan Sub-assembly
      *2 O-ring
      *3 Oil Filter Cap
      *a No Gap

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note


      • After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

      • Do not cross thread the oil filter cap.

    7. A01VG8XE06
      Text in Illustration
      *1 Oil Filter Drain Plug
      *2 Drain Plug O-ring

      Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

      Note

      Before installing the drain plug O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. Install the oil filter drain plug to the oil filter cap.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Be careful that the drain plug O-ring does not get caught between the parts.

  4. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving", or ILSAC multigrade engine oil

      • 0W-20


      • 5W-20


      • 5W-30


      • 10W-30
      API grade SL, SM or SN multigrade engine oil

      • 15W-40


      • 20W-50
      Standard Capacity
      Item Specified Condition
      Drain and refill with oil filter change 3.4 liters (3.6 US qts, 3.0 Imp. qts)
      Drain and refill without oil filter change 3.2 liters (3.4 US qts, 2.8 Imp. qts)
      Dry fill 3.9 liters (4.1 US qts, 3.4 Imp. qts)

    2. Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.

  5. INSPECT FOR ENGINE OIL LEAK