OIL PUMP COMPONENTS
ILLUSTRATION
| *1 | INTAKE MANIFOLD GASKET | *2 | OIL LEVEL DIPSTICK GUIDE SUB-ASSEMBLY |
| *3 | OIL LEVEL DIPSTICK GUIDE O-RING | *4 | OIL LEVEL DIPSTICK SUB-ASSEMBLY |
| *5 | SUPERCHARGER BRACKET | *6 | SUPERCHARGER ASSEMBLY |
| *7 | NO. 1 VACUUM TRANSMITTING HOSE | *8 | PLATE WASHER |
| *9 | FUEL VAPOR FEED HOSE | *10 | VENTILATION HOSE |
| *11 | WATER BY-PASS HOSE | *12 | NO. 2 WATER BY-PASS HOSE |
| *a | For use with SST | *b | For use with a union nut wrench |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | FUEL TUBE SUB-ASSEMBLY | *2 | FUEL DELIVERY PIPE |
| *3 | WASHER | *4 | PLATE |
| *5 | O-RING | *6 | FUEL INJECTOR ASSEMBLY |
| *7 | INJECTOR VIBRATION INSULATOR | *8 | NO. 1 DELIVERY PIPE SPACER |
| *9 | WATER INLET | *10 | GASKET |
| *11 | THERMOSTAT | *12 | INTERCOOLER RESERVE TANK BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | EXHAUST MANIFOLD | *2 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
| *3 | EXHAUST MANIFOLD TO HEAD GASKET | *4 | MANIFOLD STAY |
| *5 | IGNITION COIL ASSEMBLY | *6 | ALTERNATOR TENSIONER BRACKET |
| *a | 18 mm (0.709 in.) | *b | 17 mm (0.669 in.) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | WATER INLET HOSE | *2 | NO. 3 WATER BY-PASS HOSE |
| *3 | VENTILATION HOSE | *4 | NO. 1 OIL COOLER HOSE |
| *5 | OIL COOLER HOSE | *6 | CRANKSHAFT POSITION SENSOR HEAT SHIELD |
| *7 | NO. 1 WATER BY-PASS PIPE | *8 | AIR TUBE |
| *9 | SUPERCHARGER NOSE SUPPORT BRACKET | *10 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CYLINDER HEAD COVER GASKET | *2 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *3 | SEAL WASHER | *4 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | STUD BOLT | *2 | O-RING |
| *3 | CRANKSHAFT PULLEY | *4 | TIMING CHAIN COVER SUB-ASSEMBLY |
| *5 | TIMING CHAIN COVER OIL SEAL | *6 | NO. 1 CHAIN TENSIONER ASSEMBLY |
| *7 | CRANKSHAFT PULLEY BOLT | *8 | WATER PUMP GASKET |
| *9 | WATER PUMP ASSEMBLY | *10 | SEAL WASHER |
| *11 | ENGINE MOUNTING BRACKET RH | *12 | OIL FILTER BRACKET |
| *13 | BRACKET | *14 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
MP grease |  |
Adhesive 1324 |
| ★ | Precoated part |  |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | CRANKSHAFT TIMING SPROCKET | *4 | NO. 1 CHAIN VIBRATION DAMPER |
| *5 | NO. 2 CHAIN SUB-ASSEMBLY | *6 | NO. 2 CHAIN VIBRATION DAMPER |
| *7 | OIL PUMP DRIVE GEAR | *8 | OIL PUMP DRIVESHAFT GEAR |
| *9 | CHAIN TENSIONER PLATE | *10 | SPRING |
| *11 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | NO. 2 OIL PAN SUB-ASSEMBLY | *2 | OIL PUMP ASSEMBLY |
| *3 | OIL PAN DRAIN PLUG | *4 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | OIL PUMP COVER SUB-ASSEMBLY | *2 | OIL PUMP RELIEF VALVE |
| *3 | OIL PUMP BODY | *4 | OIL PUMP DRIVEN ROTOR |
| *5 | OIL PUMP DRIVE ROTOR | *6 | OIL PUMP RELIEF VALVE SPRING |
| *7 | OIL PUMP RELIEF VALVE PLUG | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |