WATER PUMP INSTALLATION

PROCEDURE


  1. INSTALL ENGINE WATER PUMP ASSEMBLY


    1. B00470MC10
      *a Protrusion

      Align the protrusion of a new gasket with the cutout in the timing chain cover sub-assembly and install the gasket in the groove of the timing chain cover sub-assembly.

      Tech Tips

      Be sure to clean the contact surfaces.

    2. B00469ZE01

      Install the engine water pump assembly to the timing chain cover assembly with the 5 bolts.

      Torque:
      Bolt (A)
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
      Bolt (B)
      25.5 N*m  { 260 kgf*cm, 19 ft.*lbf }
      Bolt Length
      Item Length
      Bolt (A) 25 mm (0.984 in.)
      Bolt (B) 35 mm (1.38 in.)
      Bolt (C) 75 mm (2.95 in.)

      Tech Tips

      As final tightening of bolt C will be performed when installing the supercharger, temporarily tighten it at this time.

  2. INSTALL SUPERCHARGER NOSE SUPPORT BRACKET

    Click here

  3. INSTALL WATER INLET HOSE


    1. Connect the water inlet hose to the cylinder block sub-assembly and slide the clip to secure it.

  4. INSTALL SUPERCHARGER ASSEMBLY

    Click here

  5. INSTALL FAN AND GENERATOR V BELT

    Click here

  6. INSPECT FAN AND GENERATOR V BELT

    Click here

  7. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH


    1. B0047AVN04

      Install the engine mounting insulator sub-assembly RH with the 5 bolts and 2 nuts.

      Torque:
      Bolt A and Nut A
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }
      Bolt B and Nut B
      88 N*m  { 897 kgf*cm, 65 ft.*lbf }

    2. Install the engine mounting stay RH with the 2 bolts.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

  8. REMOVE ENGINE SUPPORT BRIDGE

    Click here

  9. REMOVE ENGINE HANGER

    Click here

  10. INSTALL BATTERY CARRIER

    Click here

  11. INSTALL BATTERY TRAY

    Click here

  12. INSTALL BATTERY

    Click here

  13. INSTALL AIR CLEANER BRACKET

    Click here

  14. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  15. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

    Click here

  16. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

    Click here

  17. CONNECT NO. 2 VENTILATION HOSE

    Click here

  18. INSTALL FRONT SUSPENSION UPPER CENTER BRACE SUB-ASSEMBLY

    Click here

  19. INSTALL OUTER COWL TOP PANEL (for LHD)

    Click here

  20. INSTALL OUTER COWL TOP PANEL (for RHD)

    Click here

  21. INSTALL INNER COWL TOP TO COWL BRACE (for LHD)

    Click here

  22. INSTALL INNER COWL TOP TO COWL BRACE (for RHD)

    Click here

  23. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)

    Click here

  24. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)

    Click here

  25. INSTALL FRONT AIR SHUTTER SEAL RH (for LHD)

    Click here

  26. INSTALL FRONT AIR SHUTTER SEAL RH (for RHD)

    Click here

  27. INSTALL WINDSHIELD WIPER MOTOR AND LINK

    Click here

  28. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  29. ADD ENGINE COOLANT

    Click here

  30. INSPECT FOR COOLANT LEAK

    Click here

  31. INSTALL ENGINE UNDER COVER RH

    Click here