CANISTER(for TMMF Made) REMOVAL

CAUTION / NOTICE / HINT

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. Click here

PROCEDURE


  1. REMOVE DECK BOARD ASSEMBLY

    Click here

  2. REMOVE SPARE WHEEL COVER

    Click here

  3. REMOVE REAR SEAT ASSEMBLY LH

    Click here

  4. REMOVE REAR SEAT ASSEMBLY RH

    Click here

  5. REMOVE REAR SEATBACK CENTER HINGE SUB-ASSEMBLY

    Click here

  6. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  8. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A01VEZ6E02
      Text in Illustration
      *1 Tube Joint Clip
      *2 Fuel Tube Joint
      *3 O-Ring
      *4 Nylon Tube
      *5 Fuel Suction Plate
      A01VL3H Widen
      A01VE7C Pull Out

      Spread the tip of the tube joint clip, and pull it out in the direction of the arrow.

    2. Disconnect the fuel main tube from the fuel tank assembly.

      Note


      • Clean off any dirt or other foreign matter from the clip before beginning work.

      • The fuel tube joint is sealed by O-rings to the fuel pump tube and the fuel suction plate, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.

      • Perform installation and removal procedures with your hands only. Never use any tools.

      • Do not forcibly bend, fold, or twist the nylon tube.

      • After disconnecting, protect the contact surfaces by covering them with a plastic bag.

      • If the nylon tube and fuel suction plate are stuck together, push them together and pull them apart to release them.

  9. SEPARATE NO. 2 FUEL EMISSION TUBE


    1. A01VEPK

      Remove the clip and disconnect the No. 2 fuel emission tube from the fuel suction plate.

  10. SEPARATE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY


    1. A01VEHX

      Disconnect the No. 1 canister outlet hose sub-assembly from the fuel suction plate.

  11. REMOVE FUEL PUMP GAUGE RETAINER

    Note

    Before performing the work, cover the connector of the fuel suction tube assembly and the tube joint with a plastic bag to prevent foreign matter from entering, and then clean off any dirt or other foreign matter.


    1. A01VGX0E01

      Install SST to the fuel pump gauge retainer.

      SST
      09808-14030   ( 09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050 )

      1. Temporarily install plate and claw to the fuel pump gauge retainer.

      2. Press claw against the rib of the fuel pump gauge retainer, and tighten bolt.

      3. Install SST handle.

    2. A01VHKUE02

      While making sure that SST does not rise up, slowly turn handle and loosen the fuel pump gage retainer.

      Note


      • Be careful not to apply excessive downward force to SST, as this may damage the fuel pump or fuel tank.

      • Turning SST at an angle may cause it to slip off of the fuel pump gauge retainer, so be sure SST is horizontal when turning.

      • To prevent damage to parts, do not turn SST too vigorously.

      • If SST slips off of the fuel pump gauge retainer, loosen SST (bolt) and install SST again.

    3. While holding down the fuel suction tube assembly, remove the fuel tank pump gauge retainer.

  12. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


    1. A01VHTCE01
      Text in Illustration
      *1 Fuel Pump Filter
      A01VL3H Direction to Bend

      After bending up the tip of the fuel pump filter and pulling it out, pull out the arm of the fuel sender gage assembly, and remove the fuel suction tube assembly from the fuel tank.

      Note


      • Be careful not to bend the arm of the fuel sender gauge assembly.

      • When installing or removing the fuel suction tube assembly, be careful of fuel splashing.

      • Do not damage the fuel pump filter.

      • When setting down the fuel suction tube assembly, make sure that its weight is not pressing on the fuel pump filter.

  13. REMOVE FUEL SUCTION TUBE SET GASKET


    1. A01VE83

      Remove the fuel suction tube set gasket.

  14. DRAIN FUEL

  15. REMOVE FUEL SENDER GAUGE ASSEMBLY

    Click here

  16. REMOVE FUEL PUMP HARNESS

    Click here

  17. REMOVE FUEL PUMP FILTER

    Click here

  18. REMOVE FUEL PUMP

    Click here

  19. REMOVE NO. 2 FUEL SUCTION SUPPORT

    Click here

  20. REMOVE FUEL PRESSURE REGULATOR ASSEMBLY

    Click here

  21. REMOVE CHARCOAL CANISTER SUB-ASSEMBLY


    1. A01VF9QE04
      Text in Illustration
      *a Lock

      Disengage the 3 claws as shown in the illustration.

    2. Release the lock, disengage the 2 claws, then slide the No. 1 fuel suction support and remove it from the charcoal canister sub-assembly.

    3. A01VE4V

      Remove the O-ring from the charcoal canister sub-assembly.