ENGINE UNIT COMPONENTS
ILLUSTRATION
| *1 | INTAKE MANIFOLD GASKET | *2 | OIL LEVEL DIPSTICK GUIDE SUB-ASSEMBLY |
| *3 | OIL LEVEL DIPSTICK GUIDE O-RING | *4 | OIL LEVEL DIPSTICK SUB-ASSEMBLY |
| *5 | SUPERCHARGER BRACKET | *6 | SUPERCHARGER ASSEMBLY |
| *7 | NO. 1 VACUUM TRANSMITTING HOSE | *8 | PLATE WASHER |
| *9 | FUEL VAPOR FEED HOSE | *10 | VENTILATION HOSE |
| *11 | WATER BY-PASS HOSE | *12 | NO. 2 WATER BY-PASS HOSE |
| *a | For use with SST | *b | For use with a union nut wrench |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | FUEL TUBE SUB-ASSEMBLY | *2 | FUEL DELIVERY PIPE |
| *3 | WASHER | *4 | PLATE |
| *5 | O-RING | *6 | FUEL INJECTOR ASSEMBLY |
| *7 | INJECTOR VIBRATION INSULATOR | *8 | NO. 1 DELIVERY PIPE SPACER |
| *9 | WATER INLET | *10 | GASKET |
| *11 | THERMOSTAT | *12 | INTERCOOLER RESERVE TANK BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *1 | EXHAUST MANIFOLD | *2 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
| *3 | EXHAUST MANIFOLD TO HEAD GASKET | *4 | MANIFOLD STAY |
| *5 | IGNITION COIL ASSEMBLY | *6 | ALTERNATOR TENSIONER BRACKET |
| *a | 18 mm (0.709 in.) | *b | 17 mm (0.669 in.) |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | WATER INLET HOSE | *2 | NO. 3 WATER BY-PASS HOSE |
| *3 | VENTILATION HOSE | *4 | NO. 1 OIL COOLER HOSE |
| *5 | OIL COOLER HOSE | *6 | CRANKSHAFT POSITION SENSOR HEAT SHIELD |
| *7 | NO. 1 WATER BY-PASS PIPE | *8 | AIR TUBE |
| *9 | SUPERCHARGER NOSE SUPPORT BRACKET | *10 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT POSITION SENSOR | *2 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
| *3 | CYLINDER HEAD COVER GASKET | *4 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *5 | ENGINE COVER JOINT | *6 | OIL FILLER CAP GASKET |
| *7 | OIL FILLER CAP SUB-ASSEMBLY | *8 | SPARK PLUG |
| *9 | SPARK PLUG TUBE GASKET | *10 | SEAL WASHER |
| *11 | GASKET | *12 | O-RING |
| *13 | BRACKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CRANKSHAFT PULLEY | *2 | ENGINE OIL PRESSURE SWITCH ASSEMBLY |
| *3 | NO. 1 CHAIN TENSIONER ASSEMBLY | *4 | TIMING CHAIN COVER OIL SEAL |
| *5 | TIMING CHAIN COVER SUB-ASSEMBLY | *6 | WATER INLET HOUSING |
| *7 | ENGINE MOUNTING BRACKET RH | *8 | WATER PUMP GASKET |
| *9 | OIL FILTER BRACKET | *10 | O-RING |
| *11 | WATER PUMP ASSEMBLY | *12 | SEAL WASHER |
| *13 | STUD BOLT | *14 | BRACKET |
| *15 | CRANKSHAFT PULLEY BOLT | *16 | OIL FILTER UNION |
| *17 | OIL FILTER SUB-ASSEMBLY | *18 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
MP grease |  |
Adhesive 1324 |
 |
Adhesive 1344 |  |
Do not apply lubricants to the threaded parts |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | CRANKSHAFT POSITION SENSOR | *4 | CRANKSHAFT TIMING GEAR KEY |
| *5 | CRANKSHAFT TIMING SPROCKET | *6 | NO. 1 CHAIN VIBRATION DAMPER |
| *7 | NO. 1 CRANKSHAFT POSITION SENSOR PLATE | *8 | NO. 2 CHAIN SUB-ASSEMBLY |
| *9 | NO. 2 CHAIN VIBRATION DAMPER | *10 | O-RING |
| *11 | OIL PUMP DRIVE GEAR | *12 | OIL PUMP DRIVE SHAFT GEAR |
| *13 | CHAIN DAMPER SPRING | *14 | CHAIN TENSIONER PLATE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT | *2 | CAMSHAFT BEARING CAP |
| *3 | CAMSHAFT HOUSING SUB-ASSEMBLY | *4 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
| *5 | CAMSHAFT TIMING GEAR ASSEMBLY | *6 | CYLINDER HEAD GASKET |
| *7 | CYLINDER HEAD SUB-ASSEMBLY | *8 | ENGINE COOLANT TEMPERATURE SENSOR |
| *9 | NO. 1 CAMSHAFT BEARING | *10 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
| *11 | NO. 2 CAMSHAFT | *12 | NO. 2 CAMSHAFT BEARING |
| *13 | OIL CONTROL VALVE FILTER | *14 | VALVE LASH ADJUSTER ASSEMBLY |
| *15 | PLATE WASHER | *16 | CYLINDER HEAD SET BOLT |
| *17 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 49 (500, 36) 2nd: turn 90° 3rd: turn 45° |
- | - |
ILLUSTRATION
| *1 | KNOCK CONTROL SENSOR | *2 | NO. 1 TAPER SCREW PLUG |
| *3 | NO. 2 OIL PAN SUB-ASSEMBLY | *4 | OIL PAN DRAIN PLUG |
| *5 | OIL PUMP ASSEMBLY | *6 | REAR ENGINE OIL SEAL |
| *7 | STIFFENING CRANKCASE ASSEMBLY | *8 | VENTILATION VALVE SUB-ASSEMBLY |
| *9 | RING PIN | *10 | STUD BOLT |
| *11 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | |
Adhesive 1324 |
| ★ | Precoated part | - | - |