ENGINE UNIT COMPONENTS
ILLUSTRATION
| *1 | EGR PIPE GASKET | *2 | EXHAUST COOLER ASSEMBLY |
| *3 | EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY | *4 | EXHAUST MANIFOLD GASKET |
| *5 | EXHAUST MANIFOLD TO HEAD GASKET | *6 | MANIFOLD STAY |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Do not apply lubricants to the threaded parts | - | - |
ILLUSTRATION
| *1 | EGR INLET GASKET | *2 | EGR VALVE ASSEMBLY |
| *3 | INTAKE MANIFOLD | *4 | NO. 1 INTAKE MANIFOLD TO HEAD GASKET |
| *5 | PURGE VALVE (PURGE VSV) | *6 | VENTILATION HOSE ASSEMBLY |
| *7 | NO. 2 FUEL VAPOR FEED HOSE | *8 | NO. 2 WATER BY-PASS HOSE |
| *9 | EGR COOLER ASSEMBLY | *10 | EGR PIPE ASSEMBLY |
| *11 | NO. 4 WATER BY-PASS HOSE | *12 | NO. 6 ENGINE WIRE |
| *13 | WATER BY-PASS HOSE | *14 | EGR VALVE BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Do not apply lubricants to the threaded parts | - | - |
ILLUSTRATION
| *A | for Manual Transaxle | *B | for CVT |
| *1 | NO. 1 IGNITION COIL | *2 | NO. 1 WATER BY-PASS PIPE |
| *3 | NO. 2 WATER BY-PASS PIPE | *4 | NO. 4 ENGINE WIRE |
| *5 | STUD BOLT | *6 | V-RIBBED BELT TENSIONER ASSEMBLY |
| *7 | WIRE HARNESS CLAMP BRACKET | *8 | NO. 6 WATER BY-PASS HOSE |
| *9 | NO. 1 WATER BY-PASS HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FUEL DELIVERY PIPE | *2 | FUEL INJECTOR ASSEMBLY |
| *3 | INJECTOR VIBRATION INSULATOR | *4 | NO. 1 DELIVERY PIPE SPACER |
| *5 | O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | OIL FILLER CAP ASSEMBLY | *2 | OIL FILLER CAP GASKET |
| *3 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY | *4 | CAMSHAFT BEARING CAP OIL HOLE GASKET |
| *5 | O-RING | *6 | CAMSHAFT TIMING CONTROL MOTOR WITH EDU ASSEMBLY |
| *7 | NO. 1 CRANK POSITION SENSOR | *8 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *9 | CYLINDER HEAD COVER GASKET | *10 | SPARK PLUG |
| *11 | PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY) | *12 | VENTILATION SYSTEM GROMMET |
| *13 | SEAL WASHER | *14 | PLATE WASHER |
| *15 | CAMSHAFT TIMING CONTROL MOTOR O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Do not apply lubricants to the threaded parts | - | - |
ILLUSTRATION
| *1 | ENGINE COOLANT TEMPERATURE SENSOR | *2 | ENGINE OIL PRESSURE SWITCH ASSEMBLY |
| *3 | CRANKSHAFT POSITION SENSOR | *4 | KNOCK SENSOR |
| *5 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Adhesive 1344 | ★ | Precoated part |
ILLUSTRATION
| *1 | WATER INLET WITH THERMOSTAT SUB-ASSEMBLY | *2 | NO. 2 WATER INLET HOUSING GASKET |
| *3 | ENGINE WATER PUMP ASSEMBLY | *4 | CRANKSHAFT PULLEY |
| *5 | STUD BOLT | *6 | TIMING CHAIN COVER OIL SEAL |
| *7 | TIMING CHAIN COVER ASSEMBLY | *8 | O-RING |
| *9 | WATER PUMP GASKET | *10 | CRANKSHAFT PULLEY SET BOLT |
| *11 | SEAL WASHER | *12 | NO. 1 TIMING GEAR COVER TIGHT PLUG |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease |  |
Adhesive 1324 |
| ★ | Precoated part | |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *1 | REAR ENGINE OIL SEAL | *2 | CRANKSHAFT TIMING GEAR KEY |
| *3 | CRANKSHAFT TIMING SPROCKET | *4 | TIMING CHAIN GUIDE |
| *5 | TIMING CHAIN TENSION ARM | *6 | NO. 1 CHAIN TENSIONER ASSEMBLY |
| *7 | CHAIN SUB-ASSEMBLY | *8 | NO. 2 CHAIN VIBRATION DAMPER |
| *9 | CHAIN TENSIONER GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *1 | OIL CONTROL VALVE FILTER | *2 | CAMSHAFT |
| *3 | NO. 2 CAMSHAFT | *4 | CAMSHAFT HOUSING SUB-ASSEMBLY |
| *5 | CAMSHAFT TIMING GEAR ASSEMBLY | *6 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
| *7 | CAMSHAFT BEARING CAP | *8 | CYLINDER BLOCK WATER JACKET SPACER |
| *9 | CYLINDER HEAD GASKET | *10 | CYLINDER HEAD SET BOLT |
| *11 | VALVE LASH ADJUSTER ASSEMBLY | *12 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
| *13 | RING PIN | *14 | CYLINDER HEAD SUB-ASSEMBLY |
| *15 | PLATE WASHER | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 32 (326, 24) 2nd: Turn 90° 3nd: Turn 90° |
- | - |
ILLUSTRATION
| *1 | OIL STRAINER SUB-ASSEMBLY | *2 | OIL PAN SUB-ASSEMBLY |
| *3 | OIL PAN DRAIN PLUG | *4 | NO. 1 OIL PAN BAFFLE PLATE |
| *5 | NO. 2 OIL PAN BAFFLE PLATE | *6 | OIL FILTER ELEMENT |
| *7 | STRAIGHT PIN | *8 | CYLINDER BLOCK SUB-ASSEMBLY |
| *9 | OIL STRAINER O-RING | *10 | NO. 1 OIL PAN GASKET |
| *11 | OIL FILTER CAP ASSEMBLY | *12 | OIL FILTER DRAIN PLUG O-RING |
| *13 | OIL FILTER CAP GASKET | *14 | OIL FILTER DRAIN PLUG |
| *15 | OIL PAN DRAIN PLUG GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Adhesive 1324 | ★ | Precoated part |