ENGINE ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Note


  • As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.

  • When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.

  • After replacing the engine assembly, perform both "Injector Compensation" and "Pilot Quantity Learning Values Reset" functions using the intelligent tester Click here.

PROCEDURE


  1. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

    A01VHRBE03

    Tech Tips

    Only perform this procedure when replacement of the engine mounting insulator RH is necessary.


    1. Temporarily tighten the engine mounting insulator RH with the 3 bolts.

    2. Fully tighten the 3 bolts, in the order shown in the illustration.

      Torque:
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }

  2. INSTALL ENGINE MOUNTING INSULATOR LH

    A01VFOME04

    Tech Tips

    Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


    1. Temporarily tighten the engine mounting insulator LH with the 5 bolts.

    2. Fully tighten the 5 bolts, in the order shown in the illustration.

      Torque:
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }

  3. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    1. Install the No. 1 crankshaft position sensor plate.

      A01VF45E05
      Text in Illustration
      *1 Mark "RR" - -
      *a Engine Block Side - -

      Note

      Install the plate with the concave surface facing the cylinder block, as shown in the illustration.

  4. INSTALL FLYWHEEL SUB-ASSEMBLY

    A01VF7IE01

    1. Using SST, hold the crankshaft.

      SST
      09213-58014
      09330-00021

    2. Clean the 6 bolts and the 6 bolt holes.

    3. A01VF4ZE54
      Text in Illustration
      *1 Adhesive

      Apply adhesive to the 2 or 3 end threads of the bolts.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
    4. A01VDRIE05

      Using several steps, uniformly install and tighten the 6 bolts in the order shown in the illustration (Procedure "A").

      Torque:
      49 N*m  { 500 kgf*cm, 36 ft.*lbf }
    5. A01VI43E03
      Text in Illustration
      *a Paint Mark

      Mark the bolts with paint as shown in the illustration.

    6. Retighten the bolts 90° in the same sequence as in procedure "A".

    7. Check that the paint marks of each bolt are at a 90° angle from the original position.

  5. INSTALL CRANKSHAFT POSITION SENSOR (w/ DPF)


    1. Install the crankshaft position sensor with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Engage the crankshaft position sensor wire harness clamp to the wire harness bracket.

    3. Connect the crankshaft position sensor connector.

  6. INSTALL CRANKSHAFT POSITION SENSOR (w/o DPF)

    Click here

  7. INSTALL ENGINE WIRE


    1. Install the engine wire to the engine.

    2. A01VHC7E12
      Text in Illustration
      *a Engine side
      *b Transaxle side

      Install the 2 ground bolts.

      Torque:
      Bolt A
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }
      Bolt B
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

  8. INSTALL CYLINDER BLOCK SIDE COVER


    1. Install the cylinder block side cover with the bolt and washer plate.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

  9. INSTALL EXHAUST MANIFOLD

    Click here

  10. TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

    Click here

  11. INSTALL TURBOCHARGER SUB-ASSEMBLY

    Click here

  12. INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

    Click here

  13. INSTALL MANIFOLD STAY

    Click here

  14. INSTALL TURBOCHARGER STAY

    Click here

  15. INSTALL NO. 2 MANIFOLD SUPPORT BRACKET (w/ DPF)


    1. Install the No. 2 manifold support bracket with the 2 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  16. INSTALL MANIFOLD SUPPORT BRACKET (w/ DPF)


    1. Install the manifold support bracket with the 3 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  17. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ DPF)

    Click here

  18. INSTALL NO. 1 TURBO INSULATOR (w/ DPF)

    Click here

  19. TEMPORARILY TIGHTEN EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/o DPF)

    Click here

  20. TEMPORARILY TIGHTEN MANIFOLD SUPPORT BRACKET (w/o DPF)

    Click here

  21. TIGHTEN EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/o DPF)

    Click here

  22. TIGHTEN MANIFOLD SUPPORT BRACKET (w/o DPF)

    Click here

  23. INSTALL NO. 1 TURBO INSULATOR (w/o DPF)

    Click here

  24. INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)


    1. A01VGEFE03
      Text in Illustration
      *a Paint Mark
      *b View A
      *c Rear Side

      Install the differential pressure sensor with the nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Connect the 2 vacuum transmitting hoses.

    3. Connect the differential pressure sensor connector.

  25. INSTALL NO. 2 ENGINE COVER BRACKET

    Click here

  26. INSTALL NO. 2 EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ DPF)

    Click here

  27. INSTALL NO. 3 MANIFOLD SUPPORT BRACKET (w/ DPF)

    Click here

  28. INSTALL NO. 4 MANIFOLD SUPPORT BRACKET (w/ DPF)

    Click here

  29. INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY (w/ DPF)

    Click here

  30. INSTALL NO. 2 VACUUM PIPE (w/ DPF)

    Click here

  31. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

    Click here

  32. INSTALL CLUTCH DISC ASSEMBLY (for Multi-Mode Manual Transaxle)

    Click here

  33. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

    Click here

  34. INSTALL CLUTCH COVER ASSEMBLY (for Multi-Mode Manual Transaxle)

    Click here

  35. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

    Click here

  36. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Multi-Mode Manual Transaxle)

    Click here

  37. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)

    Click here

  38. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Multi-Mode Manual Transaxle)

    Click here

  39. INSTALL BLEEDER CLUTCH RELEASE TUBE (for Manual Transaxle)

    Click here

  40. INSTALL BLEEDER CLUTCH RELEASE TUBE (for Multi-Mode Manual Transaxle)

    Click here

  41. INSPECT CLUTCH PIPE LINE (for Manual Transaxle)

    Click here

  42. INSPECT CLUTCH PIPE LINE (for Multi-Mode Manual Transaxle)

    Click here

  43. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)

    Click here

  44. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Multi-Mode Manual Transaxle)

    Click here

  45. INSTALL BLEEDER TO ACCUMULATOR TUBE (for Manual Transaxle)

    Click here

  46. INSTALL BLEEDER CLUTCH RELEASE TUBE (for Multi-Mode Manual Transaxle)

    Click here

  47. INSTALL ENGINE ASSEMBLY (for Manual Transaxle)

    A01VJS2E01
    Text in Illustration
    *1 Reverse Restrict Pin Assembly
    *2 Outer Select Lever

    1. Hook the outer select lever of the manual transaxle to the reverse restrict pin assembly to secure it.

    2. Make sure that the knock pins are not loose, bent, damaged or scratched and then install the engine to the manual transaxle with the contact surfaces of the engine and manual transaxle flat against each other.

    3. Align the input shaft with the clutch disc and install the engine to the manual transaxle.

    4. A01VLKEE01
      Text in Illustration
      *1 Knock Pin Hole

      Install the 8 bolts.

      Torque:
      for Flange Bolt
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      for Bolt with Washer
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }

      Note

      Insert knock pins into the knock pin holes securely so that the end face of the transaxle fits close against the engine before tightening the bolts.

  48. INSTALL ENGINE ASSEMBLY (for Multi-Mode Manual Transaxle)


    1. Make sure that the knock pins are not loose, bent, damaged or scratched and then install the engine to the manual transaxle with the contact surfaces of the engine and transaxle flat against each other.

    2. Align the input shaft with the clutch disc and install the engine to the manual transaxle.

    3. A01VLKEE01
      Text in Illustration
      *1 Knock Pin Hole

      Install the 8 bolts.

      Torque:
      for Flange Bolt
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      for Bolt with Washer
      33 N*m  { 337 kgf*cm, 24 ft.*lbf }

      Note

      Insert knock pins into the knock pin holes securely so that the end face of the transaxle fits close against the engine before tightening the bolts.

  49. INSTALL STARTER ASSEMBLY

    Click here

  50. INSTALL NO. 2 AIR TUBE ASSEMBLY


    1. Insert the No. 1 air hose to the throttle body.

    2. A01VHW1E01
      Text in Illustration
      *1 No. 1 Air Hose
      *a View A
      *b Front Side
      *c RH Side

      Install the No. 2 air tube assembly with the bolt.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

    3. Tighten the hose clamp.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

      Tech Tips

      Check the torque in an hour after tightening and confirm that it is 1.8 N*m or higher.

  51. INSTALL NO. 2 RADIATOR HOSE


    1. A01VE9LE01
      Text in Illustration
      *a View A
      *b Upper Side
      *c RH Side

      Install the No. 2 radiator hose.

  52. INSTALL WATER BY-PASS HOSE ASSEMBLY


    1. A01VINJE01
      Text in Illustration
      *a View A
      *b Upper Side

      Install the water by-pass hose assembly.

  53. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE


    1. Place wooden blocks or plate lift attachments on an engine lifter, and then set the engine assembly with transaxle.

      Note


      • Place the wooden blocks or plate lift attachments so that the engine assembly with transaxle is level.

      • As the engine assembly with transaxle is very heavy, be sure to support it securely.

    2. Operate the engine lifter and lift the engine assembly with transaxle and the front suspension crossmember to the position where the engine mounting insulators RH and LH can be installed.

    3. Install the engine mounting insulator LH with the through bolt and nut.

      Torque:
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }

      Tech Tips

      Tighten by holding the nut and turning the bolt.

    4. A01VEL8E02

      Install the engine mounting insulator RH with the bolt and 3 nuts.

      Torque:
      Bolt
      88 N*m  { 897 kgf*cm, 65 ft.*lbf }
      Nut A
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }
      Nut B
      88 N*m  { 897 kgf*cm, 65 ft.*lbf }

    5. Install the engine mounting stay with the 2 bolts.

      Torque:
      88 N*m  { 897 kgf*cm, 65 ft.*lbf }

    6. By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

      A01VHZEE04
      Text in Illustration
      *a Datum Hole *b OK
      *c NG - -
      A01VL3H Front of the Vehicle - -
      SST
      09670-00010
      Torque:
      Bolt A
      87 N*m  { 887 kgf*cm, 64 ft.*lbf }
      Bolt B
      151 N*m  { 1540 kgf*cm, 111 ft.*lbf }
      Bolt C
      98 N*m  { 999 kgf*cm, 72 ft.*lbf }

      Note


      • Insert SST into the datum hole vertically.

      • If impossible to insert SST vertically, loosen all bolts and then insert SST again.

  54. INSTALL OIL PAN COVER

    Click here

  55. INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click here

  56. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  57. INSTALL FRONT FLOOR CENTER BRACE

    Click here

  58. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

    Click here

  59. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

    Click here

  60. INSTALL COLUMN HOLE COVER SILENCER SHEET

    Click here

  61. CONNECT TRANSAXLE WIRE (for Multi-Mode Manual Transaxle)


    1. Connect the 5 connectors and 2 clamps.

  62. CONNECT ENGINE WIRE


    1. Engage the 2 claws and connect the wire harness to the junction block.

    2. Connect the 2 connectors to the engine junction block.

    3. Engage the wire harness clamp.

    4. Connect the ground wire with the bolt.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }

    5. Install the engine room junction block cover.

    6. A01VI56

      Connect the ECM connector and engage the harness clamp.

    7. Engage the wire harness clamp and connect the current sensor connector and glow relay connector.

    8. Connect the 3 connectors to the positive (+) battery terminal.

  63. INSTALL CLUTCH HOSE

    Click here

  64. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

    Click here

  65. INSTALL NO. 1 AIR TUBE

    A01VLDKE02
    Text in Illustration
    *1 No. 1 Air Hose
    *a View A
    *b Front Side
    *c RH Side

    1. Insert the No. 1 air hose to the turbocharger.

    2. Install the No. 1 air tube with the 2 nuts.

      Torque:
      20 N*m  { 199 kgf*cm, 14 ft.*lbf }

    3. Tighten the hose clamp.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    4. Connect the wire harness with the bolt.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }

  66. INSTALL NO. 3 AIR HOSE

    A01VFD4E03
    Text in Illustration
    *a View A
    *b View B
    *c Upper Side
    *d Rear Side

    1. Install the No. 3 air hose.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  67. CONNECT NO. 2 RADIATOR HOSE


    1. A01VIW1E05
      Text in Illustration
      *a View A
      *b Upper Side
      *c RH Side

      Connect the No. 2 radiator hose.

  68. INSTALL NO. 1 RADIATOR HOSE


    1. A01VEXPE03
      Text in Illustration
      *a View A
      *b View B
      *c Upper Side
      *d LH Side

      Install the No. 1 radiator hose.

  69. INSTALL NO. 2 AIR HOSE

    A01VI6CE02
    Text in Illustration
    *a View A
    *b View B
    *c Upper Side
    *d Rear Side

    1. Install the No. 2 air hose with the hose clamp.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  70. CONNECT INLET HEATER WATER HOSE


    1. A01VIWUE02
      Text in Illustration
      *a View A
      *b Upper Side
      *c Front Side

      Connect the inlet heater water hose.

  71. CONNECT OUTLET HEATER WATER HOSE


    1. A01VEUGE02
      Text in Illustration
      *a View A
      *b Upper Side
      *c LH Side

      Connect the outlet heater water hose.

  72. CONNECT NO. 2 FUEL HOSE SUB-ASSEMBLY

    A01VIU2E01
    Text in Illustration
    *a View A
    *b View B
    *c Upper Side
    *d Front Side

    1. Connect the No. 2 fuel hose sub-assembly.

  73. CONNECT UNION TO CONNECTOR TUBE HOSE


    1. Connect the union to connector tube hose.

  74. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY (w/ Air Conditioning System)

    Click here

  75. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Air Conditioning System)

    Click here

  76. CONNECT COOLER REFRIGERANT SUCTION HOSE NO.1 (w/ Air Conditioning System)

    Click here

  77. INSTALL FAN AND GENERATOR V BELT

    Click here

  78. INSPECT FAN AND GENERATOR V BELT

    Click here

  79. INSTALL BATTERY CARRIER (for LHD)


    1. Install the battery carrier with the 5 bolts.

      Torque:
      17 N*m  { 175 kgf*cm, 13 ft.*lbf }

    2. Engage the 3 clamps and connect the wire harness onto the battery carrier.

  80. INSTALL BATTERY CARRIER (for RHD)


    1. Install the battery carrier with the 5 bolts.

      Torque:
      17 N*m  { 175 kgf*cm, 13 ft.*lbf }

    2. Engage the 4 clamps and connect the wire harness onto the battery carrier.

  81. INSTALL BATTERY TRAY


    1. Install the battery tray onto the battery carrier.

  82. INSTALL BATTERY


    1. Install the battery onto the battery tray.

    2. Install the battery clamp with the 2 nuts.

      Torque:
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

    3. Connect the cable to the positive (+) battery terminal.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  83. INSTALL AIR CLEANER BRACKET


    1. Install the air cleaner No. 1 bracket with the 3 bolts.

      Torque:
      20 N*m  { 199 kgf*cm, 14 ft.*lbf }

  84. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Torque:
    5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  85. FILL CLUTCH ACTUATOR RESERVOIR WITH BRAKE FLUID (for Multi-Mode Manual Transaxle)

    Click here

  86. BLEED CLUTCH LINE

    Click here

  87. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  88. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

    Click here

  89. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE

    A01VJZ2E03
    Text in Illustration
    *a Front Side
    *b RH Side
    *c Upper Mark

    1. Connect the No. 1 air cleaner hose to the turbocharger and fasten the air cleaner hose clamp.

    2. Connect the ventilation hose to the cylinder head cover.

    3. Connect the fuel hose to the hose clamp.

    4. Install the air cleaner cap onto the air cleaner case, then hang the 2 lock clamps.

    5. Fit the wire harness into the air cleaner cap.

    6. Engage the 4 wire harness clamps.

    7. Connect the mass air flow meter connector.

  90. INSTALL RADIATOR RESERVE TANK BRACKET


    1. Install the radiator reserve tank bracket with the bolt.

      Torque:
      20 N*m  { 199 kgf*cm, 14 ft.*lbf }

  91. INSTALL RADIATOR RESERVE TANK ASSEMBLY


    1. Install the reserve tank with the bolt.

      Torque:
      20 N*m  { 199 kgf*cm, 14 ft.*lbf }
    2. A01VM7PE03
      Text in Illustration
      *1 No. 4 Water By-pass Hose
      *2 Water By-pass Hose Assembly
      *a View A
      *b View B
      *c Upper Side
      *d Rear Side
      *e Paint Mark

      Engage the hose clamp and connect the water by-pass hose assembly.

      Note

      Align the water by-pass hose assembly paint mark with the clamp center.

    3. Connect the No. 4 water by-pass hose.

  92. INSTALL OUTER COWL TOP PANEL (for LHD)

    Click here

  93. INSTALL OUTER COWL TOP PANEL (for RHD)

    Click here

  94. INSTALL INNER COWL TOP TO COWL BRACE (for LHD)

    Click here

  95. INSTALL INNER COWL TOP TO COWL BRACE (for RHD)

    Click here

  96. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)

    Click here

  97. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)

    Click here

  98. INSTALL FRONT AIR SHUTTER SEAL RH (for LHD)

    Click here

  99. INSTALL FRONT AIR SHUTTER SEAL RH (for RHD)

    Click here

  100. INSTALL FRONT WIPER MOTOR AND LINK

    Click here

  101. ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

    Click here

  102. ADD MANUAL TRANSAXLE OIL (for Multi-Mode Manual Transaxle)

    Click here

  103. FILL RESERVOIR WITH BRAKE FLUID

    Click here

  104. INSPECT FLUID LEVEL

    Click here

  105. ADD ENGINE OIL

    Click here

  106. ADD ENGINE COOLANT

    Click here

  107. BLEED AIR FROM FUEL SYSTEM

    Click here

  108. INITIALIZATION AND REGISTRATION

    Click here

  109. INITIALIZATION OF MULTI-MODE MANUAL TRANSAXLE ECU (for Multi-Mode Manual Transaxle)

    Click here

  110. LEARNING OF MULTI-MODE MANUAL TRANSAXLE SYSTEM (for Multi-Mode Manual Transaxle)

    Click here

  111. SYNCHRONIZATION POSITION CALIBRATION (for Multi-Mode Manual Transaxle)

    Click here

  112. CHARGE REFRIGERANT (w/ Air Conditioning System)

    Click here

  113. INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)

    Click here

  114. INSPECT MANUAL TRANSAXLE OIL (for Multi-Mode Manual Transaxle)

    Click here

  115. CHECK ENGINE OIL LEVEL

    Click here

  116. INSPECT FOR OIL LEAK

    Click here

  117. INSPECT FOR COOLANT LEAK

    Click here

  118. CHECK FUEL LEAK

    Click here

  119. INSPECT FOR EXHAUST GAS LEAK

  120. WARM UP ENGINE (w/ Air Conditioning System)

  121. INSPECT FOR REFRIGERANT LEAK (w/ Air Conditioning System)

    Click here

  122. INSTALL NO. 1 ENGINE COVER

    A01VEHME02
    Text in Illustration
    *1 Pin
    *2 Grommet
    *3 Hook
    *4 Bracket

    1. Attach the No. 1 engine cover hooks to the bracket. Then align the No. 1 engine cover grommets with the 2 pins, and press down on the No. 1 engine cover to attach the pins.

  123. INSTALL ENGINE UNDER COVER RH

    Torque:
    5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  124. INSTALL ENGINE UNDER COVER LH

    Torque:
    5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  125. INSTALL CENTER ENGINE UNDER COVER

    Torque:
    5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  126. INSTALL FRONT WHEELS

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  127. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  128. CHECK SPEED SENSOR SIGNAL (w/o VSC)

    Click here

  129. CHECK SPEED SENSOR SIGNAL (w/ VSC)

    Click here