SFI SYSTEM Fuel Injector Circuit

DESCRIPTION

The fuel injectors inject fuel based on the signals from the ECM.

WIRING DIAGRAM

A01VJ15E01
A01VJ15E02

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)


    1. A01VG1VE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Fuel Injector Assembly)

      Disconnect the fuel injector assembly connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B5-2 - Body ground Ignition switch ON 11 to 14 V
      B7-2 - Body ground Ignition switch ON 11 to 14 V
      B9-2 - Body ground Ignition switch ON 11 to 14 V
      B11-2 - Body ground Ignition switch ON 11 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY) Click here

    OK

  2. INSPECT FUEL INJECTOR (INJECTION AND VOLUME)


    1. Check the fuel injector injection and volume Click here.

      Tech Tips

      Perform "Inspection After Repairs" after replacing the fuel injector assembly Click here.


    NG

    REPLACE FUEL INJECTOR ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)


    1. Disconnect the ECM connector.

    2. Disconnect the fuel injector assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      B5-1 - B22-20 (#10) Always Below 1 Ω
      B7-1 - B22-17 (#20) Always Below 1 Ω
      B9-1 - B22-18 (#30) Always Below 1 Ω
      B11-1 - B22-19 (#40) Always Below 1 Ω
      B5-1 or B22-20 (#10) - Body ground Always 10 kΩ or higher
      B7-1 or B22-17 (#20) - Body ground Always 10 kΩ or higher
      B9-1 or B22-18 (#30) - Body ground Always 10 kΩ or higher
      B11-1 or B22-19 (#40) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      B5-1 - B23-20 (#10) Always Below 1 Ω
      B7-1 - B23-17 (#20) Always Below 1 Ω
      B9-1 - B23-18 (#30) Always Below 1 Ω
      B11-1 - B23-19 (#40) Always Below 1 Ω
      B5-1 or B23-20 (#10) - Body ground Always 10 kΩ or higher
      B7-1 or B23-17 (#20) - Body ground Always 10 kΩ or higher
      B9-1 or B23-18 (#30) - Body ground Always 10 kΩ or higher
      B11-1 or B23-19 (#40) - Body ground Always 10 kΩ or higher

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)


    1. Disconnect the fuel injector assembly connector.

    2. Remove the No. 1 integration relay from the engine room relay block.

    3. Disconnect the No. 1 integration relay connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B5-2 - 1E-2 Always Below 1 Ω
      B7-2 - 1E-2 Always Below 1 Ω
      B9-2 - 1E-2 Always Below 1 Ω
      B11-2 - 1E-2 Always Below 1 Ω
      B5-2 or 1E-2 - Body ground Always 10 kΩ or higher
      B7-2 or 1E-2 - Body ground Always 10 kΩ or higher
      B9-2 or 1E-2 - Body ground Always 10 kΩ or higher
      B11-2 or 1E-2 - Body ground Always 10 kΩ or higher

    OK

    CHECK ECM POWER SOURCE CIRCUIT Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR