ECD SYSTEM(w/o DPF) Turbocharger Noise

DESCRIPTION

Tech Tips

Turbocharger noise is classified into 2 types. One is whistling noise, and the other is whining noise. When troubleshooting, the type of noise should be determined first.

Description
Noise Type Noise Description Main Trouble Area
Whistling noise The volume and pitch of this noise are proportional to turbocharger sub-assembly speed or engine speed. Therefore, the noise level will become more obvious when engine speed increases.

  • Turbocharger sub-assembly (e.g. shaft imbalance)

  • Gears inside engine

  • Transmission gear

  • Intake air system leakage

  • Intake air system breakage
Whining noise This noise has a lower pitch than whistling noise. It generally occurs in the engine speed range of 1500 to 2500 rpm, and has a relatively constant pitch, independent of engine speed and vehicle speed.

Turbocharger sub-assembly

Tech Tips


  • Example: Vibration of turbocharger sub-assembly is transferred to exhaust pipe which causes resonation and noise.

  • Example: Vibration of turbocharger sub-assembly is transferred through exhaust pipe to vehicle body (floor) which then vibrates causing noise.

  1. Faults and Symptoms of Diesel Engine Components

    Turbocharger System
    Main fault Turbocharger turbine shaft imbalance
    Symptoms

    High-pitched whistling noise

    Tech Tips

    The pitch and volume change in proportion to the turbocharger speed.
    Intake System
    Main fault Leakage
    Symptoms Leak flow noise
    Gear inside Engine
    Symptoms

    Gear noise

    Tech Tips

    The pitch and volume change in proportion to the engine speed.
    Transmission Gear
    Symptoms

    Gear noise

    Tech Tips

    The pitch and volume change in proportion to the transmission gear speed.

PROCEDURE


  1. CONFIRM CONDITION IN WHICH NOISE OCCURRED


    1. Confirm with the customer the conditions in which the noise occurred.

      Tech Tips

      To clearly understand the conditions in which the noise occurred, the items in the table below are useful.

      Item Note
      Engine speed Engine speed range
      Vehicle speed Vehicle speed range
      Transmission gear Which gear?
      Accelerator pedal position During acceleration or deceleration?
      Temperature

      • Ambient temperature

      • Engine temperature (cold, warmed up, etc.)
      Road conditions

      • City or highway driving

      • Uphill or downhill
      Noise level

      • Did the noise occur suddenly, or build gradually?

      • Has the noise gradually been getting louder?
      Other symptoms

      • Lack of power

      • High fuel consumption, etc.
      Noise recognition What made the customer determine the noise to be abnormal?

    NEXT

  2. CONFIRM NOISE CUSTOMER MENTIONED (PROCEDURE 2)


    1. Check for the noise described by the customer.

      Tech Tips

      If a noise is heard, make sure that the noise matches the noise described by the customer.

      Result
      Result Proceed to
      Obvious abnormal noise matching noise described by customer is confirmed A
      Obvious abnormal noise matching noise described by customer is not confirmed B

    B

    EXPLAIN TO THE CUSTOMER THAT THE NOISE IS NORMAL Click here

    A

  3. CHECK INTAKE SYSTEM


    1. Check for air leakage between the air cleaner and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold Click here.

      Tech Tips


      • Check for disconnected or improperly connected hoses, and gaps between hoses and parts.

      • Check for foreign matter between the air cleaner and turbocharger sub-assembly.


    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS

    OK

  4. CONFIRM NOISE SOURCE (FROM TURBOCHARGER OR NOT)


    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and warm it up.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VN Turbo Open.

    5. Perform the Active Test and rev the engine up several times.

    6. Check whether the noise is reduced or not compared with the noise under the condition that the Active Test is not performed.

      Result
      Result Proceed to
      The noise is reduced (or disappears) A
      The noise is the same as in Procedure 2 (The noise does not change) B

      Tech Tips


      • When the variable nozzle of the turbocharger sub-assembly opens fully regardless of the engine condition, the turbocharger sub-assembly speed slows down and the cause of noise can be confirmed that is from the turbocharger sub-assembly or not.

      • If the turbocharger sub-assembly is the cause of the noise, the noise will be reduced when the variable nozzle opens because turbocharger sub-assembly speed does not increase.


    B

    CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 7) Click here

    A

  5. CONFIRM NOISE TYPE


    1. Check whether the noise can be heard even when the engine speed is more than 3000 rpm, and whether the noise gradually gets louder as the engine speed increases.

      Tech Tips

      If so, the noise is likely to be whistling noise. If not, the noise is likely to be whining noise.

      Result
      Result Proceed to
      Yes (The noise is likely to be whistling noise) A
      No (The noise is likely to be whining noise) B

    A

    REPLACE TURBOCHARGER SUB-ASSEMBLY Click here

    B

  6. PERFORM ALIGNMENT OF EXHAUST PIPE AND CONFIRM THE NOISE


    1. Disconnect the exhaust pipe at the ball joint and from each exhaust pipe support, and then realign the exhaust pipe and reconnect it to each exhaust pipe support and at the ball joint Click here.

      A01VESIE01
      Text in Illustration
      *1 Front Exhaust Pipe Assembly *2 Tail Exhaust Pipe Assembly
      *3 Exhaust Pipe Support *4 Compression Spring
      *5 Gasket (Ball Joint) - -
      *a Specified Torque *b Non-reusable Part

      Tech Tips

      Above illustration is an example.

    2. Confirm whether the noise problem is solved or not.

      Tech Tips

      The alignment of the exhaust pipe affects whining noise.

      Result
      Result Proceed to
      The noise problem is solved A
      The noise problem remains B

    A

    END

    B

    REPLACE TURBOCHARGER SUB-ASSEMBLY Click here

  7. CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 7)


    1. Check for the noise source with a sound scope.

      Note

      When performing this check, make sure that the sound scope, your body, etc., do not get caught on the V-belt.

      Tech Tips


      • The source of the noise is not the turbocharger sub-assembly, but a part other than the turbocharger sub-assembly (e.g. a part inside the engine, transmission, or vacuum pump).

      • Sometimes gear noise may be mistaken for turbocharger sub-assembly noise. For gear noise, pay attention to the gear inside the engine and transmission gear.

      • Rev the engine up and check if the noise reduces at the same time the engine speed decreases. If the noise reduces at the same time the engine speed decreases, it is gear noise. If the noise reduces a short time after the engine speed decreases, it is turbocharger sub-assembly noise.

      • The following illustration is a reference for checking whether the noise source is from the engine.

      A01VLCVE01
      Text in Illustration
      *1 Vacuum Pump *2 Camshaft
      *3 Supply Pump Assembly *4 Chain Tensioner Slipper
      *5 Chain Sub-assembly *6 Chain Vibration Damper
      *7 Oil Pump *8 No. 2 Chain Sub-assembly
      *a Gear Location inside Engine - -

      Tech Tips


      • Above illustration is an example.

      • Gear noise can be confirmed with a sound scope. Put the sound scope on the cylinder block near the gear, and if the noise heard through the sound scope has the same timing as the noise heard without the sound scope, it is gear noise.


    NEXT

  8. REPLACE THE PARTS DETECTED IN PROCEDURE 7


    1. Replace the parts detected in Procedure 7 as the noise source.


    NEXT

  9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Check whether the noise problem has been successfully solved.


    NEXT

    END

  10. EXPLAIN TO THE CUSTOMER THAT THE NOISE IS NORMAL


    1. Explain to the customer that the noise the customer mentioned is not abnormal.

      Tech Tips

      To help the customer understand, test driving another car with the customer may be helpful.


    NEXT

    END