ECD SYSTEM(w/o DPF), Diagnostic DTC:P0489, P0490

DTC Code DTC Name
P0489 Exhaust Gas Recirculation Control Circuit Low
P0490 Exhaust Gas Recirculation Control Circuit High

DESCRIPTION

The ECM opens and closes the EGR valve using a DC motor type actuator. Due to opening and closing the valve, the exhaust gas recirculation volume can be properly controlled.

P0489
DTC Detection Drive Pattern DTC Detection Condition Trouble Area

Turn the ignition switch to ON and wait for 10 seconds

(Monitor this DTC only once per driving cycle)

Open in electric EGR control valve assembly circuit

(2 trip detection logic)

  • Electric EGR control valve assembly

  • Open in electric EGR control valve assembly circuit

  • ECM
P0490
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 30 seconds

Short in electric EGR control valve assembly circuit

(2 trip detection logic)

  • Electric EGR control valve assembly

  • Short in electric EGR control valve assembly circuit

  • ECM

WIRING DIAGRAM

Refer to DTC P0405 Click here.

CAUTION / NOTICE / HINT

Note

When replacing the ECM, the ECM needs Registration and Initialization Click here.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the intelligent tester. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the tester display.

  • Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

    4. When changing the Active Test value from 0 to 100%, check that Actual EGR Valve Pos. smoothly changes to the set opening angle.

      OK
      Value smoothly changes to the set opening angle.

    OK

    CHECK WHETHER DTC OUTPUT RECURS (DTC P0489 OR P0490) Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTORL VALVE ASSEMBLY - ECM)


    1. Disconnect the electric EGR control valve assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B21-23 (EGM+) - B55-1 (M+) Always Below 1 Ω
      B21-22 (EGM-) - B55-2 (M-) Always Below 1 Ω
      B21-23 (EGM+) or B55-1 (M+) - Body ground Always 10 kΩ or higher
      B21-22 (EGM-) or B55-2 (M-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  3. INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (DC MOTOR)


    1. Inspect the electric EGR control valve assembly Click here.


    OK

    REPLACE ECM Click here

    NG

  4. REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY


    1. Replace the electric EGR control valve assembly Click here.

    2. Turn the ignition switch to ON.

    3. Turn the ignition switch off and wait for 30 seconds or more.


    NEXT

    CHECK WHETHER DTC OUTPUT RECURS (DTC P0489 OR P0490) Click here

  5. REPAIR OR REPLACE HARNESS OR CONNECTOR


    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0489 OR P0490)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON and wait for 30 seconds or more.

    6. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

    7. Read the pending DTCs.

      Result
      Result Proceed to
      DTC P0489 or P0490 A
      No DTC output B

    B

    END

    A

  7. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

  8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON and wait for 30 seconds or more.

    6. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

    7. Confirm that the pending DTC is not output again.


    NEXT

    END