ECD SYSTEM(w/ DPF), Diagnostic DTC:P0697

DTC Code DTC Name
P0697 Sensor Reference Voltage "C" Circuit / Open

DESCRIPTION

Refer to DTC P0122 Click here.

Refer to DTC P2122 Click here.

P0697
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON

Power voltages (5 V as standard) supplied from ECM to accelerator pedal position sensor and diesel throttle position sensor are lower or higher than appropriate thresholds.

(1 trip detection logic)

  • Diesel throttle body assembly (throttle position sensor)

  • Open or short in diesel throttle position sensor circuit

  • Accelerator pedal sensor assembly (accelerator pedal position sensor assembly)

  • Open or short in accelerator pedal position sensor circuit

  • ECM

WIRING DIAGRAM

Refer to DTC P0122 Click here.

Refer to DTC P2122 Click here.

CAUTION / NOTICE / HINT

Note

When replacing the ECM, the ECM needs Registration and Initialization Click here.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the intelligent tester. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the tester display.

  • Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0697)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Enter the following menus: Powertrain / Engine and ECT / DTC.

    4. Read DTCs.

      Result
      Result Proceed to
      DTC P0697 A
      DTC P0697 and other DTCs B

      Tech Tips

      If any DTCs other than P0697 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)


    1. Disconnect the diesel throttle body assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B29-5 (VC) - A59-46 (VCTA) Always Below 1 Ω
      B29-6 (VTA) - A59-45 (VTA1) Always Below 1 Ω
      B29-3 (E2) - A59-47 (ETA) Always Below 1 Ω
      B29-5 (VC) or A59-46 (VCTA) - Body ground Always 10 kΩ or higher
      B29-6 (VTA) or A59-45 (VTA1) - Body ground Always 10 kΩ or higher
      B29-3 (E2) or A59-47 (ETA) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (VC VOLTAGE)


    1. A01VJEIE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Diesel Throttle Body Assembly)

      Disconnect the diesel throttle body assembly connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B29-5 (VC) - B29-3 (E2) Ignition switch ON 4.5 to 5.5 V

    NG

    REPLACE ECM Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)


    1. Disconnect the accelerator pedal sensor assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A36-4 (VCPA) - A59-56 (VCPA) Always Below 1 Ω
      A36-6 (VPA) - A59-55 (VPA) Always Below 1 Ω
      A36-5 (EPA) - A59-57 (EPA) Always Below 1 Ω
      A36-1 (VCP2) - A59-53 (VCP2) Always Below 1 Ω
      A36-3 (VPA2) - A59-52 (VPA2) Always Below 1 Ω
      A36-2 (EPA2) - A59-54 (EPA2) Always Below 1 Ω
      A36-4 (VCPA) or A59-56 (VCPA) - Body ground Always 10 kΩ or higher
      A36-6 (VPA) or A59-55 (VPA) - Body ground Always 10 kΩ or higher
      A36-5 (EPA) or A59-57 (EPA) - Body ground Always 10 kΩ or higher
      A36-1 (VCP2) or A59-53 (VCP2) - Body ground Always 10 kΩ or higher
      A36-3 (VPA2) or A59-52 (VPA2) - Body ground Always 10 kΩ or higher
      A36-2 (EPA2) or A59-54 (EPA2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (VC VOLTAGE)


    1. A01VLGBE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Accelerator Pedal Sensor Assembly)

      Disconnect the accelerator pedal sensor assembly connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      A36-4 (VCPA) - A36-5 (EPA) Ignition switch ON 4.5 to 5.5 V
      A36-1 (VCP2) - A36-2 (EPA2) Ignition switch ON 4.5 to 5.5 V

    NG

    REPLACE ECM Click here

    OK

  6. REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)


    1. Replace the accelerator pedal sensor assembly Click here.


    NEXT

  7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0697)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON.

    6. Enter the following menus: Powertrain / Engine and ECT / DTC.

    7. Read the DTC.

      Result
      Result Proceed to
      No DTC output A
      DTC P0697 B

    A

    END

    B

  8. REPLACE DIESEL THROTTLE BODY ASSEMBLY (THROTTLE POSITION SENSOR)


    1. Replace the diesel throttle body assembly Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  9. REPAIR OR REPLACE HARNESS OR CONNECTOR


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  10. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

  11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the tester on.

    3. Clear the DTCs Click here.

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON.

    6. Enter the following menus: Powertrain / Engine and ECT / DTC.

    7. Confirm that the DTC is not output again.


    NEXT

    END