| Pedal height from floor panel (for LHD) | for 1KR-FE | 125.2 to 135.2 mm (4.93 to 5.32 in.) |
| for 2NR-FKE | 125.2 to 135.2 mm (4.93 to 5.32 in.) | |
| for 2ZR-FE | 125.3 to 135.3 mm (4.93 to 5.33 in.) | |
| for 1ND-TV | 139.4 to 149.4 mm (5.49 to 5.88 in.) | |
| Pedal height from No. 3 dash panel insulator pad (for RHD) | except 1ND-TV | 125.5 to 135.5 mm (4.94 to 5.33 in.) |
| for 1ND-TV | 135.5 to 145.5 mm (5.33 to 5.73 in.) | |
| Pedal free play | - | 5.0 to 15.0 mm (0.197 to 0.591 in.) |
| Push rod play at pedal top | - | 1.0 to 5.0 mm (0.0394 to 0.197 in.) |
| Clutch release point from pedal full stroke end position | - | 25 mm (0.984 in.) or more |
| Pedal stroke (for LHD) (Reference) |
except 1ND-TV | 125 to 135 mm (4.92 to 5.31 in.) |
| for 1ND-TV | 140 to 150 mm (5.51 to 5.91 in.) | |
| Pedal stroke (for RHD) (Reference) |
except 1ND-TV | 125 to 135 mm (4.92 to 5.31 in.) |
| for 1ND-TV | 137 to 147 mm (5.39 to 5.79 in.) | |
| Clutch start switch clearance | for LHD except 1ND-TV | 2.0 to 5.0 mm (0.0787 to 0.197 in.) |
| for LHD 1ND-TV | 2.5 to 5.5 mm (0.0984 to 0.217 in.) | |
| for RHD | 2.5 to 5.5 mm (0.0984 to 0.217 in.) | |
| No. 2 clutch start switch clearance (for RHD) | except 1ND-TV | 1.3 to 4.3 mm (0.0512 to 0.169 in.) |
| for 1ND-TV | 0.5 to 3.5 mm (0.0197 to 0.138 in.) |
| Standard voltage (combined dry cell battery voltage of 4.5 V) | ||
| 1 (VSR1) - 2 (E2R1) | Sensor angle: 55° | Approximately 4.05 V |
| Sensor angle: 0° | Approximately 2.25 V | |
| Sensor angle: -55° | Approximately 0.45 V | |
| 4 (VSR2) - 5 (E2R2) | Sensor angle: 55° | Approximately 4.05 V |
| Sensor angle: 0° | Approximately 2.25 V | |
| Sensor angle: -55° | Approximately 0.45 V | |
| Reference voltage (combined dry cell battery voltage of 5.0 +/- 0.3 V) | ||
| 1 (VSR1) - 2 (E2R1) | Sensor angle: 55° | Approximately 4.5 V |
| Sensor angle: 0° | Approximately 2.5 V | |
| Sensor angle: -55° | Approximately 0.5 V | |
| 4 (VSR2) - 5 (E2R2) | Sensor angle: 55° | Approximately 4.5 V |
| Sensor angle: 0° | Approximately 2.5 V | |
| Sensor angle: -55° | Approximately 0.5 V | |
| Clutch disc rivet depth | Minimum | 0.3 mm (0.0118 in.) |
| Clutch disc runout | Maximum | 0.8 mm (0.0315 in.) |
| Clutch cover diaphragm spring wear | Maximum depth | 0.5 mm (0.0197 in.) |
| Maximum width | 6.0 mm (0.236 in.) | |
| Flywheel runout | Maximum | 0.1 mm (0.00394 in.) |
| Clutch cover diaphragm spring tip non-alignment | Maximum | 0.5 mm (0.0197 in.) |
| Clutch start switch assembly | ||
| Standard resistance 1 - 2 |
ON (Pushed in) | Below 1 Ω |
| OFF (Released) | 10 kΩ or higher | |
| No. 2 clutch start switch assembly | ||
| Standard resistance 1 - 2 |
ON (Pushed in) | Below 1 Ω |
| OFF (Released) | 10 kΩ or higher | |