Click here

WINDSHIELD OUTSIDE MOULDING REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the windshield glass removal/installation are shown below.

Table 1. Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

  • for Stereo Camera Type:

  • Windshield glass (Removal and installation)

 Adjust object recognition camera

  • Dynamic radar cruise control system (for Stereo camera type)

  • Front camera system (for Stereo camera type)

  • Lane control system (for Stereo camera type)

  • Road sign assist system (for Stereo camera type)

  • Pre-collision system (for Stereo camera type)

  • Automatic high beam system

Click here

  • for Mono Camera Type:

  • Windshield glass (Removal and installation)

 Adjust forward recognition camera

  • Forward recognition camera system (for Mono camera type)

  • Dynamic radar cruise control system (for Mono camera type)

  • Lane-keeping assist system (for Mono camera type)

  • Pre-collision system (for Mono camera type)

  • Automatic high beam system

Click here
Tip:

  • Use the same procedure for the RH and LH side.

  • The following procedure is for the LH side.

Click here

PROCEDURE


  1. Click here

    REMOVE LOWER WINDSHIELD OUTSIDE MOULDING LH


    1. B004WHRC01
      B004VGX Protective Tape

      Put protective tape around the lower windshield outside moulding LH.

    2. B004S3CC01
      B004RMI Remove in this Direction

      Detach the claw as shown in the illustration.

    3. B004SBK

      Using a moulding remover, detach the claw and remove the lower windshield outside moulding LH.

  2. Click here

    REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

    Tip:

    Perform the following procedure only when replacement of a No. 1 windshield outside moulding clip is necessary.


    1. B004SYJC01
      B004RMI Remove in this Direction

      Detach the claw as shown in the illustration to remove the 5 No. 1 windshield outside moulding clips.

  3. Click here

    REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

    Tip:

    Perform the following procedure only when replacement of a No. 3 windshield outside moulding clip is necessary.


    1. Remove the windshield glass sub-assembly.

      Click here

    2. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    3. B004YFLC07
      *a Tape

      Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Standard Measurement
      Area Measurement
      A 5.0 mm (0.197 in.)
      Note:

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    4. B004RW3C02
      *a Flange

      Lightly press the drill against the No. 3 windshield outside moulding clips to drill off the No. 3 windshield outside moulding clip flanges, and remove the 5 No. 3 windshield outside moulding clips.

      CAUTION:

      Be careful of the drilled No. 3 windshield outside moulding clips, as they may be hot.

      Note:

      • Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

      • Prying the No. 3 windshield outside moulding clips with the drill may damage the No. 3 windshield outside moulding clip installation holes or drill bit.

    5. Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.