ROCKER PANEL MOULDING REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL NO. 1 ROCKER PANEL MOULDING PROTECTOR (ALUMINUM TAPE)

    Tech Tips

    When installing the No. 1 rocker panel moulding protector, heat the body rocker panel moulding assembly LH.

    Standard
    Item Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)

    1. Clean the body rocker panel moulding assembly LH surface.


      1. Remove the double-sided tape from the body rocker panel moulding assembly LH.

      2. Wipe off any tape adhesive residue with cleaner.

        Note


        • Installing the body rocker panel moulding assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until sufficiently removed it.

        • Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

    2. B004XDHC02
      *A for Front Side
      *B for Rear Side
      B004VGX Primer

      Apply primer to body rocker panel moulding assembly LH on the installation area of the No. 1 rocker panel moulding protector using a brush or felt.

      Note


      • Replace the brush or felt if it is dirty or has become hardened.

      • Keep any painted surface free from primer.

      • If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

      • Do not touch surfaces to which primer has been applied until the No. 1 rocker panel moulding protector has been attached.

    3. Let the primer dry sufficiently.

      Note

      Do not touch applied surfaces until the primer is dry.

      Recommended drying time
      10 minutes or more (at 23 °C (73 °F))

    4. Remove the peeling paper of the new No. 1 rocker panel moulding protector trying not to touch the adhesional surface.

    5. for Front Side:


      1. B004V19C01
        *a Mark-off Line

        Align the No. 1 rocker panel moulding protector with the mark-off line on the body rocker panel moulding assembly LH and install it as shown in the illustration.

        Tech Tips

        Press the No. 1 rocker panel moulding protector firmly to install it.

    6. for Rear Side:


      1. B004U6CC01
        *a Mark-off Line

        Align the No. 1 rocker panel moulding protector with the mark-off line on the body rocker panel moulding assembly LH and install it as shown in the illustration.

        Tech Tips

        Press the No. 1 rocker panel moulding protector firmly to install it.

  2. INSTALL NO. 1 ROCKER PANEL MOULDING PROTECTOR (CAULKING SPONGE)

    Tech Tips

    When installing the No. 1 rocker panel moulding protector, heat the body rocker panel moulding assembly LH.

    Standard
    Item Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B004UGDC23
    *a Heated Part
    *b Heat Light

    1. Clean the body rocker panel moulding assembly LH surface.


      1. Remove the double-sided tape from the body rocker panel moulding assembly LH.

      2. Wipe off any tape adhesive residue with cleaner.

        Note


        • Installing the body rocker panel moulding assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until sufficiently removed it.

        • Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

    2. Apply primer to body rocker panel moulding assembly LH on the installation area of the No. 1 rocker panel moulding protector using a brush or felt.

      Note


      • Replace the brush or felt if it is dirty or has become hardened.

      • Keep any painted surface free from primer.

      • If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

      • Do not touch surfaces to which primer has been applied until the No. 1 rocker panel moulding protector has been attached.

      B004X8BC02
      B004VGX Primer - -

    3. Let the primer dry sufficiently.

      Note

      Do not touch applied surfaces until the primer is dry.

      Recommended drying time
      10 minutes or more (at 23 °C (73 °F))

    4. Remove the peeling paper of the new No. 1 rocker panel moulding protector trying not to touch the adhesional surface.

    5. Align the No. 1 rocker panel moulding protector with the mark-off line on the body rocker panel moulding assembly LH and install it as shown in the illustration.

      Tech Tips

      Press the No. 1 rocker panel moulding protector firmly to install it.

      B004W9NC01
      *a Mark-off Line - -

  3. INSTALL FRONT ROCKER PANEL MOULDING END COVER LH

    Tech Tips

    When installing the front rocker panel moulding end cover LH, heat the body rocker panel moulding assembly LH.

    Standard
    Item Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B004UGDC23
    *a Heated Part
    *b Heat Light

    1. Clean the body rocker panel moulding assembly LH surface.


      1. Remove the double-sided tape from the body rocker panel moulding assembly LH.

      2. Wipe off any tape adhesive residue with cleaner.

        Note


        • Installing the body rocker panel moulding assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until sufficiently removed it.

        • Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

    2. B004WYJC02
      *A for Front Side
      *B for Rear Side
      B004VGX Primer

      Apply primer to body rocker panel moulding assembly LH on the installation area of the front rocker panel moulding end cover LH using a brush or felt.

      Note


      • Replace the brush or felt if it is dirty or has become hardened.

      • Keep any painted surface free from primer.

      • If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

      • Do not touch surfaces to which primer has been applied until the front rocker panel moulding end cover LH has been attached.

    3. Let the primer dry sufficiently.

      Note

      Do not touch applied surfaces until the primer is dry.

      Recommended drying time
      10 minutes or more (at 23 °C (73 °F))

    4. Remove the peeling paper of the new front rocker panel moulding end cover LH trying not to touch the adhesional surface.

    5. for Front Side:


      1. B004XJL

        Align the front rocker panel moulding end cover LH with the mark-off line on the body rocker panel moulding assembly LH and install it as shown in the illustration.

        Tech Tips

        Press the front rocker panel moulding end cover LH firmly to install it.

    6. for Rear Side:


      1. B004XGLC02
        *a Mark-off Line

        Install the front rocker panel moulding end cover LH as shown in the illustration.

        Tech Tips

        Press the front rocker panel moulding end cover LH firmly to install it.

  4. INSTALL NO. 1 SIDE MUDGUARD PROTECTOR

    Tech Tips

    When installing the No. 1 side mudguard protector, heat the body rocker panel moulding assembly LH.

    Standard
    Item Temperature
    Body Rocker Panel Moulding Assembly LH 20 to 30°C (68 to 86°F)

    CAUTION:


    • Do not touch the heat light and heated parts.

    • Touching the heat light may result in burns.

    • Touching heated parts for a long time may result in burns.

    B004UGDC23
    *a Heated Part
    *b Heat Light

    1. Clean the body rocker panel moulding assembly LH surface.


      1. Remove the double-sided tape from the body rocker panel moulding assembly LH.

      2. Wipe off any tape adhesive residue with cleaner.

        Note


        • Installing the body rocker panel moulding assembly LH with some double-sided tape remaining may cause poor adhesion. Perform this procedure until sufficiently removed it.

        • Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

    2. B004SZZC02
      B004VGX Primer

      Apply primer to body rocker panel moulding assembly LH on the installation area of the No. 1 side mudguard protector using a brush or felt.

      Note


      • Replace the brush or felt if it is dirty or has become hardened.

      • Keep any painted surface free from primer.

      • If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

      • Do not touch surfaces to which primer has been applied until the No. 1 side mudguard protector has been attached.

    3. Let the primer dry sufficiently.

      Note

      Do not touch applied surfaces until the primer is dry.

      Recommended drying time
      10 minutes or more (at 23 °C (73 °F))

    4. Remove the peeling paper of the new No. 1 side mudguard protector trying not to touch the adhesional surface.

    5. B004TE9

      Install the No. 1 side mudguard protector as shown in the illustration.

  5. INSTALL ROCKER PANEL MOULDING COVER LH


    1. Attach the clip to install the rocker panel moulding cover LH as shown in the illustration.

    2. Install the 2 clips.

      B004VXBC01
      B004RMI Install in this Direction - -