Click here

WASHER MOTOR REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

Note:

Be sure to read the "PRECAUTION" thoroughly before servicing (w/ Air Suspension).

Click here

Click here

PROCEDURE


  1. Click here

    REMOVE UPPER RADIATOR SUPPORT SEAL

    Click here

  2. Click here

    REMOVE FRONT FENDER REINFORCEMENT SUB-ASSEMBLY TOP LH

    Click here

  3. Click here

    REMOVE FRONT WHEEL

    Click here

  4. Click here

    REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 2WD)

    Click here

  5. Click here

    REMOVE TRANSMISSION UNDER COVER (for 2WD)

    Click here

  6. Click here

    REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (for 2WD)

    Click here

  7. Click here

    REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for AWD)

    Click here

  8. Click here

    REMOVE FRONT WHEEL OPENING EXTENSION PAD LH


    1. B004R2J

      Remove the 2 screws and front wheel opening extension pad LH.

  9. Click here

    REMOVE ENGINE SIDE COVER LH (for 2WD)


    1. B004V87

      Remove the 4 clips.

    2. Detach the claw and remove the engine side cover LH.

  10. Click here

    REMOVE FRONT FENDER WHEEL OPENING MOULDING LH


    1. B004YO9

      Detach the claw and remove the front fender wheel opening moulding LH.

  11. Click here

    REMOVE FRONT FENDER LINER LH


    1. B004X5L

      Remove the 5 screws.

    2. B004WWE

      Remove the 7 clips.

    3. Remove the 2 screws.

    4. B004RTQ

      for 2WD:


      1. Remove the 3 clips.

    5. B004UZM

      for AWD:


      1. Remove the 4 clips.

    6. B004RQK

      Remove the 5 screws.

    7. B004X33C01
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Bend the front fender liner LH inward, slide the duct to the lower side of the vehicle and remove the front fender liner LH as shown in the illustration.

  12. Click here

    REMOVE WINDSHIELD WASHER JAR ASSEMBLY


    1. B004S0W

      Disconnect the 2 windshield washer hose assemblies as shown in the illustration.

      Note:

      Make sure to disconnect the windshield washer hose assembly as shown in the illustration to prevent improper installation during reinstallation.

    2. B004X77

      Detach the claw and disconnect the head light cleaner hose as shown in the illustration.

      Tip:

      Prepare a container before performing the procedure.

    3. B004S3RC03
      B004SZX Bolt
      B004UK4 Connector

      Remove the 2 bolts as shown in the illustration.

    4. Detach the claw.

    5. Disconnect the 2 connectors.

    6. Detach the claw and remove the No. 1 washer bracket.

    7. B004UFYC02
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Remove the 2 bolts.

    8. Slide in the direction indicated by the arrow shown in the illustration and detach the guide to remove the windshield washer jar assembly.

      Note:

      Do not damage the vehicle with the washer inlet.

      Tip:

      Washer fluid remains in the windshield washer jar assembly. Therefore, prepare a container to collect the washer fluid.

    9. Drain the washer fluid remaining in the windshield washer jar.

  13. Click here

    REMOVE WASHER HOSE PROTECTOR


    1. B004URM

      Disconnect the wire harness from the wire harness clamp.

    2. B004RUC

      Detach the 3 clips and remove the washer hose protector.

  14. Click here

    REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY


    1. B004R1IC01
      B004RMI Remove in this Direction
      B004SZX Washer hoses
      B004UK4 Connector

      Disconnect the 2 washer hoses.

    2. Disconnect the connector.

    3. Remove the windshield washer motor and pump assembly as shown in the illustration.