Click here

FRONT SEAT OUTER BELT ASSEMBLY INSPECTION

Click here
Click here Click here

PROCEDURE


  1. Click here

    INSPECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/o Pre-collision Seat Belt)

    CAUTION:
    B004S1R

    • The front seat outer belt assembly LH contains an internal pretensioner, so when performing component inspection, make sure not to accidentally connect the auxiliary battery to the pretensioner connector terminal.

    • If the auxiliary battery is connected to the pretensioner connector terminal, the pretensioner will activate, which could result in serious injury.


    1. Check the seat belt tension reducer operation.


      1. B004WLMC07
        *a

        Component without harness connected

        (Front Seat Outer Belt Assembly LH)

        Check the operating sound.

        OK
        Tester Connection Specified Condition

        L61-1 (IG) - Auxiliary battery positive (+)

        L61-2 (L) - Auxiliary battery negative (-)

        		 Operating sound is heard when the magnetized solenoid is attracting the plunger

      2. Pull out the seat belt again, disconnect the negative (-) lead of the auxiliary battery and allow the seat belt to retract. Listen to the operating sound again and check that the operating sound volume has increased.

        If the result is not as specified, replace the front seat outer belt assembly LH.

    2. B004V26C02
      *a Unlock
      *b Lock
      *c 45°

      Before installing the front seat outer belt assembly LH, check the ELR function.

      Note:

      Do not disassemble the retractor.


      1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

        If the result is not as specified, replace the front seat outer belt assembly LH.

  2. Click here

    INSPECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Pre-collision Seat Belt)

    CAUTION:
    B004S1R

    • The front seat outer belt assembly LH contains an internal pretensioner, so when performing component inspection, make sure not to accidentally connect the auxiliary battery to the pretensioner connector terminal.

    • If the auxiliary battery is connected to the pretensioner connector terminal, the pretensioner will activate, which could result in serious injury.


    1. B004SULC06
      *a

      Component without harness connected

      (Front Seat Outer Belt Assembly LH)

      Check the motor operation.

      OK
      Tester Connection Specified Condition

      L27-1 (MOL+) - Auxiliary battery positive (+)

      L27-2 (MOL-) - Auxiliary battery negative (-)

      		 Motor operates and seat belt webbing is wound
      If the result is not as specified, replace the front seat outer belt assembly LH.
    2. B004WBWC01
      *a Unlock
      *b Lock
      *c 45°

      Before installing the front seat outer belt assembly LH, check the ELR function.

      Note:

      Do not disassemble the retractor.


      1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

        If the result is not as specified, replace the front seat outer belt assembly LH.

  3. Click here

    INSPECT FRONT SEAT OUTER BELT ASSEMBLY RH (w/o Pre-collision Seat Belt)

    CAUTION:
    B004S1R

    • The front seat outer belt assembly RH contains an internal pretensioner, so when performing component inspection, make sure not to accidentally connect the auxiliary battery to the pretensioner connector terminal.

    • If the auxiliary battery is connected to the pretensioner connector terminal, the pretensioner will activate, which could result in serious injury.


    1. Check the seat belt tension reducer operation.


      1. B004WLMC08
        *a

        Component without harness connected

        (Front Seat Outer Belt Assembly RH)

        Check the operating sound.

        OK
        Tester Connection Specified Condition

        L35-1 (IG) - Auxiliary battery positive (+)

        L35-2 (L) - Auxiliary battery negative (-)

        		 Operating sound is heard when the magnetized solenoid is attracting the plunger

      2. Pull out the seat belt again, disconnect the negative (-) lead of the auxiliary battery and allow the seat belt to retract. Listen to the operating sound again and check that the operating sound volume has increased.

        If the result is not as specified, replace the front seat outer belt assembly RH.

    2. B004V26C03
      *a Unlock
      *b Lock
      *c 45°

      Before installing the front seat outer belt assembly RH, check the ELR function.

      Note:

      Do not disassemble the retractor.


      1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

        If the result is not as specified, replace the front seat outer belt assembly RH.

  4. Click here

    INSPECT FRONT SEAT OUTER BELT ASSEMBLY RH (w/ Pre-collision Seat Belt)

    CAUTION:
    B004S1R

    • The front seat outer belt assembly RH contains an internal pretensioner, so when performing component inspection, make sure not to accidentally connect the auxiliary battery to the pretensioner connector terminal.

    • If the auxiliary battery is connected to the pretensioner connector terminal, the pretensioner will activate, which could result in serious injury.


    1. B004SULC07
      *a

      Component without harness connected

      (Front Seat Outer Belt Assembly RH)

      Check the motor operation.

      OK
      Tester Connection Specified Condition

      L26-1 (MOR+) - Auxiliary battery positive (+)

      L26-2 (MOR-) - Auxiliary battery negative (-)

      		 Motor operates and seat belt webbing is wound
      If the result is not as specified, replace the front seat outer belt assembly RH.
    2. B004WBWC02
      *a Unlock
      *b Lock
      *c 45°

      Before installing the front seat outer belt assembly RH, check the ELR function.

      Note:

      Do not disassemble the retractor.


      1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

        If the result is not as specified, replace the front seat outer belt assembly RH.