Click here

REAR SEAT ASSEMBLY(for Fixed Seat Type) REASSEMBLY

Click here
Click here

CAUTION / NOTICE / HINT

CAUTION:
B004XN9

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

Tip:

A bolt without a torque specification is shown in the standard bolt chart.

Click here

Click here

PROCEDURE


  1. Click here

    INSTALL USB CHARGER SOCKET

    Click here

  2. Click here

    INSTALL REAR CONSOLE BOX WIRE


    1. B004UZ2

      Connect the connector and attach the wire harness clamps.

    2. B004UQ7

      Attach the wire harness to the hooks and install the rear console box wire.

    3. B004SVQ

      Attach the hooks and install the rear center seat armrest box.

  3. Click here

    INSTALL REAR SEAT ARMREST PLATE


    1. B004YP2C01
      *a Guide A
      *b Guide B
      B004RMI Install in this Direction

      Insert the guide B and attach the claws.

    2. Insert guide A while pressing down on the center armrest lock sub-assembly button.

    3. Install the rear seat armrest plate with 4 screws.

  4. Click here

    INSTALL REAR SEAT LOCK HANDLE KNOB


    1. B004V3DC01
      B004RMI Install in this Direction

      Attach the claws and install the rear seat lock handle knob.

  5. Click here

    INSTALL REAR CENTER SEAT ARMREST DOOR SUB-ASSEMBLY


    1. B004UTR

      Install the 2 screws with the rear center seat armrest door opened.

    2. B004UA6

      With the rear center seat armrest door closed, install the rear center seat armrest door with the 2 screws.

  6. Click here

    INSTALL REAR CENTER SEAT ARMREST PANEL SUB-ASSEMBLY


    1. B004VBSC01
      B004RMI Install in this Direction

      Attach the claws and install the rear center seat armrest panel sub-assembly.

  7. Click here

    INSTALL REAR CENTER SEAT ARMREST CUP HOLDER SUB-ASSEMBLY


    1. B004X4BC01
      B004RMI Install in this Direction

      Insert in the installation direction shown in the illustration and install the rear center seat armrest cup holder sub-assembly with the 2 screws.

  8. Click here

    INSTALL REAR POWER SEAT SWITCH

    Click here

  9. Click here

    INSTALL REAR CENTER NO. 2 SEAT ARMREST PANEL


    1. B004VNM

      Connect the connector.

    2. B004TXEC01
      B004RMI Install in this Direction

      Insert the guides and install the rear center seat armrest panel No. 2 with the 3 screws.

  10. Click here

    INSTALL REAR CENTER NO. 2 SEAT ARMREST PANEL SUB-ASSEMBLY


    1. B004W78C01
      B004RMI Install in this Direction

      Push in the installation direction shown in the illustration, attach the claws and install the rear center No. 2 seat armrest panel sub-assembly.

  11. Click here

    INSTALL CENTER ARMREST HINGE COVER


    1. B004VHR

      Pass the rear console wire through the hole in the center armrest hinge cover.

    2. Attach the wire harness clamp.

    3. B004WTS

      Attach the clips.

    4. B004YK0

      Attach the clips and install the center armrest hinge cover.

  12. Click here

    INSTALL REAR CENTER SEAT ARMREST HINGE


    1. B004S6LC01
      B004RMI Install in this Direction

      Insert the rear center seat armrest hinge in the installation direction shown in the illustration to attach the clips.

    2. Attach the wire harness clamp.

    3. Install the rear center seat armrest hinge with the screw and bush.

  13. Click here

    INSTALL SUB SEATBACK BRACKET


    1. B004W1MC01
      B004RMI Install in this Direction

      Insert the sub seatback bracket in the installation direction shown in the illustration.

    2. Install the sub seatback bracket with the nut.

  14. Click here

    INSTALL REAR SEAT AIRBAG ASSEMBLY LH

    Click here

  15. Click here

    INSTALL REAR SEAT AIRBAG ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  16. Click here

    INSTALL SEAT COVER WIRE

    Tip:

    Use the same procedure for the opposite side.


    1. B004TPHN01

      Install the seat cover wire.

      Tip:

      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 290 mm (11.4 in.) B 220 mm (8.66 in.)
      C 190 mm (7.48 in.) D 450 mm (1.48 ft.)
      E 430 mm (1.41 ft.) F 260 mm (10.2 in.)
      B004V9X
      Tip:

      The dimension shown in the illustration is the length.

  17. Click here

    INSTALL SEPARATE TYPE REAR SEATBACK COVER LH

    Tip:

    When installing a separate type rear seatback cover LH, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. Set the separate type rear seatback cover LH.

    2. B004SC4C01
      *a Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seatback cover LH to the bench type rear seatback pad with 14 new hog rings in the order indicated in the illustration.

      Note:

      • Be careful not to damage the separate type rear seatback cover LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.

    3. B004TFE

      Through the hole of the separate type rear seatback pad to the back side.

    4. B004YOVC01
      *a Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seatback cover LH to the bench type rear seatback pad with 15 new hog rings.

      Note:

      • Be careful not to damage the separate type rear seatback cover LH.

      • Be sure to tighten the hog rings securely as shown in the illustration.

    5. B004S69C02
      B004RMI Install in this Direction (1)
      B004T3S Install in this Direction (2)

      Install the strap in the installation direction (1) shown in the illustration.

    6. Install the strap in the installation direction (2) shown in the illustration.

    7. Install a new nut.

      5.5 N*m 56 kgf*cm 49 in.*lbf

    8. w Seat Heater System:


      1. B004TR4

        Attach the wire harness clamp.

      2. Connect the connector and install the rear seat wire LH.

      3. B004UDU

        Attach the clamp and install the seat heater control sub-assembly LH.

      4. Connect the connector.

      5. B004XP4

        Attach the wire harness clamp.

    9. B004VPQC01
      *a Hog Ring Pliers

      Using hog ring pliers, install 3 new hog rings.

      Note:

      • Be careful not to damage the separate type rear seatback cover LH.

      • Be sure to tighten the hog rings securely as shown in the illustration.

  18. Click here

    INSTALL SEPARATE TYPE REAR SEATBACK COVER RH

    Tip:

    Use the same procedure described for the LH side.

  19. Click here

    INSTALL REAR CENTER SEAT ARMREST ASSEMBLY


    1. B004UJUC01
      B004RMI Install in this Direction

      Lower in the installation direction shown in the illustration, attach the hooks and install the rear seat center armrest assembly with the 2 nuts.

      20 N*m 204 kgf*cm 15 ft.*lbf
  20. Click here

    INSTALL REAR SEAT HEADREST SUPPORT


    1. B004WJGC01
      B004RMI Install in this Direction

      Attach the claws and install the 6 rear seat headrest supports.

  21. Click here

    INSTALL REAR SEAT HEADREST ASSEMBLY

    Tip:

    Use the same procedure for the other side.


    1. Install the rear seat headrest assembly.

  22. Click here

    INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


    1. Install rear center seat headrest assembly.

  23. Click here

    INSTALL SEAT COVER WIRE


    1. B004SRDN01

      Install the seat cover wire.

      Tip:

      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 390 mm (1.28 ft.) B 310 mm (1.02 ft.)
      C 230 mm (9.06 in.) D 220 mm (8.66 in.)
      E 170 mm (6.69 in.) - -
      B004V9X
      Tip:

      The dimension shown in the illustration is the length.

  24. Click here

    INSTALL REAR NO. 2 SEAT WIRE RH (w/ Occupant Detection Sensor)


    1. B004XKB

      Connect the 3 connectors.

    2. Attach the wire harness clamp and install the rear No. 2 seat wire RH.

  25. Click here

    INSTALL BENCH TYPE REAR SEAT CUSHION COVER

    Tip:

    When installing a bench type rear seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B004SPZC01
      *a Hog Ring Pliers - -

      Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 26 new hog rings in the order indicated in the illustration.

      Note:

      • Be careful not to damage the bench type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.

    2. B004WCX

      Pass the strap of the bench type rear seat cushion cover to the rear side through the hole in the bench type rear seat cushion pad.

    3. B004XGSC01
      *a Hog Ring Pliers - -

      Using hog ring pliers, install 4 new hog rings.

      Note:

      • Be careful not to damage the bench type rear seat cushion cover.

      • Be sure to tighten the hog rings securely as shown in the illustration.

    4. B004TUCC01
      *a Hog Ring Pliers - -

      Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 10 new hog rings.

      Note:

      • Be careful not to damage the bench type rear seat cushion cover.

      • Be sure to tighten the hog rings securely as shown in the illustration.

    5. B004YEA

      Attach the hooks.

    6. Install the 2 clips.