FRONT SEAT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • This may result in injury.

B004YMT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL UPPER SEAT TRACK RAIL COVER


    1. B004XCRC01
      B004RMI Install in this Direction

      Attach the claw to install the upper seat track rail cover.

      Tech Tips

      Use the same procedure for the other locations.

  2. INSTALL REAR UPPER SEAT TRACK COVER


    1. B004RSS

      Connect the No. 1 terminal of the motor to the positive (+) auxiliary battery terminal, and the No. 4 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the rearmost position.

    2. B004TV4C01
      B004RMI Install in this Direction

      Attach the claw and install the rear upper seat track cover.

      Tech Tips

      Use the same procedure for the other locations.

    3. B004SA6

      Connect the No. 4 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then align the slide motor to the matchmark on the front seat adjuster assembly LH.

  3. INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH (w/ Front Passenger Side Folding Headrest)


    1. B004RH7C01
      B004RMI Install in this Direction

      Insert the guide and install the front inner seat track bracket cover LH.

  4. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH (w/ Front Passenger Side Folding Headrest)

    Tech Tips

    Use the same procedure described for the front inner seat track bracket cover LH.

  5. INSTALL REAR INNER SEAT TRACK BRACKET COVER LH (w/ Front Passenger Side Folding Headrest)


    1. B004YKTC01
      B004RMI Install in this Direction

      Rotate in the installation direction shown in the illustration to temporarily install the rear inner seat track bracket cover LH.

    2. B004RM6C01
      B004RMI Install in this Direction

      Slide in the installation direction shown in the illustration, insert the guide and install the rear inner seat track bracket cover LH.

  6. INSTALL REAR INNER SEAT TRACK BRACKET COVER LH (w/ Front Passenger Side Folding Headrest)

    Tech Tips

    Use the same procedure described for the front seat rear inner track bracket cover RH.

  7. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH


    1. B004X90C01
      B004RMI Install in this Direction

      Insert the guide, attach the claw and install the front lower seat cushion shield LH.

  8. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH (w/ Front Passenger Side Folding Headrest)

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH (w/ Climate Control Seat System)


    1. B004X62C01
      *a Clamp
      *b Guide
      B004RMI Install in this Direction

      Push in the installation direction shown in the illustration to attach the clamp.

    2. Align the guide and install the seat cushion climate control blower assembly LH with the 2 bolts.

      Torque:
      3.2 N*m  { 33 kgf*cm, 28 in.*lbf }

    3. Attach the claw and install the connector.

  10. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side with Occupant Classification System)

    Click here

  11. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


    1. B004WXBC01
      B004RMI Install in this Direction

      Attach the claw and install the seat heater control sub-assembly LH.

  12. INSTALL POSITION CONTROL ECU ASSEMBLY

    Click here

  13. INSTALL FRONT SEAT WIRE LH


    1. B004SRGC01
      *A w/ Seat Heater System
      B004RMI Install in this Direction

      Attach the claw.

    2. Attach the claw and install the connector.

    3. Attach the wire harness clamp and install the front seat wire LH.

    4. w/ Seat Heater System:


      1. Connect the 5 connectors.

    5. w/o Seat Heater System:


      1. Connect the 4 connectors.

  14. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side with Occupant Classification System)


    1. B004X7P

      Attach the claw and connect the connector.

    2. Attach the wire harness clamps and install the front seat wire RH.

    3. Connect the 2 connector.

  15. INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER RH (for Front Passenger Side)


    1. B004UCGC01
      B004RMI Install in this Direction

      Slide in the installation direction shown in the illustration and set the front seat cushion wire harness holder RH.

    2. Attach the claw and install the 3 screws.

    3. B004R89

      for Occupant Classification System:


      1. Attach the wire harness clamp.

      2. Connect the 2 connectors.

    4. Attach the wire harness clamp.

      B004RMCC01
      *A w/ Climate Control Seat System *B w/o Ottoman
      *C w/ Ottoman - -

    5. w/ Climate Control Seat System:


      1. Attach the wire harness clamp.

      2. Connect the 2 connectors.

  16. INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER LH


    1. B004UKZC02
      B004RMI Install in this Direction

      Slide in the installation direction shown in the illustration and set the front seat cushion wire harness holder LH.

    2. Attach the claw and install the 3 screws.

    3. Attach the wire harness clamp.

      B004SIJC01
      *A w/ Ottoman - -

    4. w/o Ottoman:


      1. Connect the connector.

    5. w/ Ottoman:


      1. Connect the 2 connectors.

  17. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH


    1. B004WE1C01
      *a Hook A
      *b Hook B
      *c Wire Harness Clamp
      B004RMI Install in this Direction (1)
      B004T3S Install in this Direction (2)

      Attach hook A from the installation direction (1) shown in the illustration.

    2. Attach the hook B from the installation direction (2) shown in the illustration and install the front seat cushion spring sub-assembly LH.

    3. Attach the wire harness clamp.

  18. INSTALL FRONT SEAT ADJUSTER SUB-ASSEMBLY LH (w/ Seat Cushion Pelvic Support)


    1. B004RORC01
      B004RMI Install in this Direction

      Slide in the installation direction shown in the illustration, attach the hook and install the front seat adjuster sub-assembly LH.

    2. Attach the claw and connect the joint.

  19. INSTALL INNER SEAT SUPPORT LH


    1. B004XMN

      w/ Seat Cushion Side Support:


      1. Install the inner seat support LH with the 2 screws.

      2. Attach the tube clamp.

    2. B004VUI

      w/o Seat Cushion Side Support:


      1. Install the inner seat support LH with the 2 screws.

  20. INSTALL OUTER SEAT SUPPORT LH


    1. B004VFK

      w/ Seat Cushion Side Support:


      1. Install the outer seat support LH with the 2 screws.

    2. B004RVI

      w/o Seat Cushion Side Support:


      1. Install the outer seat support LH with the 2 screws.

  21. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH


    1. B004Y1XC01
      *a Guide
      *b Hook
      B004RMI Install in this Direction (1)
      B004T3S Install in this Direction (2)
      B004U7U Install in this Direction (3)

      Slide in the installation direction (1) shown in the illustration and insert the guide.

    2. Attach the claw.

    3. Attach the hook to install the front lower seat cushion shield LH.

  22. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH


    1. B004VOHC01
      *a Guide
      *b Hook
      B004RMI Install in this Direction (1)
      B004T3S Install in this Direction (2)
      B004U7U Install in this Direction (3)

      Slide in the installation direction (1) shown in the illustration to insert the guide.

    2. Attach the claw.

    3. Attach the hook to install the front lower seat cushion RH.

  23. INSTALL SEAT RECLINING ADJUSTER INSIDE COVER LH


    1. B004XG7C01
      *a Clamp
      *b Tube Clamp
      B004RMI Install in this Direction

      Push in the installation direction shown in the illustration to attach the hook and claw and install the reclining adjuster inside cover LH

    2. w/ Seat Cushion Side Support:


      1. Install the tube to the clamp.

        Note

        Check that the tube marking is within the specified range of the clamp.

        B004U3P

  24. INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the seat reclining adjuster inside cover LH.

  25. INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004SHJC01
      B004RMI Install in this Direction

      Attach the hook and install the seat cushion main stretcher cushion assembly.

    2. B004RXYC01
      *a Strap
      *b Yellow Tube Color
      *c Green Tube Color
      *d Orange Tube Color
      *e Blue Tube Color

      Pass the tube of the seat cushion main stretcher cushion assembly through the hole and strap of the separate type front seat pad.

  26. INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004W9AC01
      B004RMI Install in this Direction

      Attach the hook and install the seat cushion main stretcher cushion assembly.

    2. B004XD4C01
      *a Strap
      *b Yellow Tube Color
      *c Green Tube Color
      *d Orange Tube Color
      *e Blue Tube Color

      Pass the tube of the seat cushion main stretcher cushion assembly through the hole and strap of the separate type front seat pad.

  27. INSTALL FRONT SEAT CUSHION COVER MAIN PAD LH (w/ Refresh Seat)


    1. Clean double-sided tape installation surface


      1. When reusing the separate type front seat cushion pad LH, remove the double-sided tape remaining on the installation surface.

    2. Remove the peeling paper from the face of the front seat cushion cover main pad LH.

      Tech Tips

      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Install the front seat cushion cover main pad LH to the position shown in the illustration.

      B004SQGC01
      *a Hog Ring Pliers - -
      B004TUP Double-sided Tape - -

      Tech Tips

      Install so that the cutout of the front seat cushion cover main pad LH fits within the mark-off line on the separate type front seat cushion pad LH.

      B004U0SC01
      *a Pad Mark-off Line
      *b Cutout

    4. Using hog ring pliers, install 4 new hog rings.

    5. Pass the strap through the hole of the separate type front seat cushion pad and use hog ring pliers to install 2 new hog rings.

  28. INSTALL SEAT COVER WIRE


    1. B004RS1N01

      Install the seat cover wire.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 80 mm (3.15 in.)
      B 170 mm (6.69 in.)
      C 200 mm (7.87 in.)
      D 280 mm (11.0 in.)

      Tech Tips

      The dimensions shown in the illustration are the length.

      B004V9X

  29. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

    Tech Tips

    When installing a separate type front seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B004YLWC01
      *a Hog Ring Pliers

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 8 new hog rings in the order indicated in the illustration.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    2. B004VFYC02
      *a Strap
      *b Band
      *c Hog Ring Pliers

      Pull out the strap from the hole of the separate type front seat cushion pad.

    3. Using hog ring pliers, install 4 new hog rings securely.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    4. Pass the band of the separate type front seat cushion cover through the separate type front seat cushion pad.

  30. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

    Note

    Perform work with the reclining adjuster inside cover on top of a box to prevent it from becoming damaged.

    B004WUB

    1. Set the separate type front seat cushion cover with pad on the front seat adjuster assembly.

    2. w/ Ottoman:


      1. Attach the clip.

        B004RHR

      2. Attach the hook.

      3. Attach the fastening tape and close the separate type front seat cushion cover.

        B004SGBC01
        B004TUP Fastening Tape - -

      4. Attach the clip.

      5. Attach the hook.

    3. w/o Ottoman:


      1. Attach the clip.

        B004RNA

      2. Attach the hook.

    4. for Front Passenger Side without Occupant Classification System:


      1. B004W6UC01
        B004RMI Install in this Direction

        Attach the claw and install the occupant detection sensor connector.

      2. B004UC8

        Connect the connector of the occupant detection sensor.

    5. B004T6M

      w/ Seat Heater System:


      1. Attach the seat cushion heater clamp and connect the connector.

    6. w/ Ottoman:


      1. B004TOTC33
        *a

        Component without harness connected

        (Ottoman Motor (Front Seat Cushion Adjuster Assembly))

        Connect the No. 4 terminal of the ottoman motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then adjust the length of the cushion to the rearmost position.

      2. B004UJS

        Connect the connector of the ottoman motor.

    7. B004TOTC33
      *a

      Component without harness connected

      (Rear Lifter Motor (Front Seat Adjuster Assembly))

      Connect the No. 4 terminal of the rear lifter motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then raise the cushion height to the lowermost position.

    8. B004TLG

      Connect the connector of the rear lifter motor.

    9. B004TOTC33
      *a

      Component without harness connected

      (Front Vertical Motor (Front Seat Adjuster Assembly))

      Connect the No. 4 terminal of the front vertical motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then raise the cushion height to the lowermost position.

    10. B004T28

      Connect the connector of the front vertical motor.

  31. INSTALL SEAT CHECK VALVE WITH HOSE LH (w/ Refresh Seat)


    1. B004R6KC01
      B004SZX Screw
      B004UK4 Joint
      B004XCB Connector

      Install the seat check valve with hose LH with the 3 screws.

    2. Connect the connector.

    3. Attach the tube clamps.

    4. Attach the claws and connect the joint.

  32. INSTALL NO. 3 INTERIOR ILLUMINATION LIGHT ASSEMBLY


    1. B004SXHC01
      B004RMI Install in this Direction

      Attach the claw and Install the No. 3 interior illumination light assembly.

  33. INSTALL FRONT SEATBACK BEZEL


    1. B004Y94C01
      B004RMI Install in this Direction

      Attach the claw and install the front seatback bezel.

  34. INSTALL FRONT SEATBACK HOOK


    1. B004U1CC01
      B004RMI Install in this Direction

      Attach the claw and install the 2 front seatback hooks.

  35. INSTALL FRONT SEATBACK EDGE PROTECTOR

    Tech Tips

    Use the same procedure for the other locations.


    1. B004S96C01
      B004RMI Install in this Direction

      Install the front seatback edge protector.

    2. B004V07

      Attach the claw.

  36. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Note

    When servicing, always hold the lumbar base and do not hold only the tube and joint areas.


    1. Push up in the installation direction (1) to install the lumbar support adjuster assembly LH.

      B004SQ5C01
      *a Lumbar Base - -
      B004RMI Install in this Direction (1) B004T3S Install in this Direction (2)

    2. Pass the tube through the hole of the front seatback frame sub-assembly LH and push in the installation direction (2) to install the lumbar support adjuster assembly LH.

    3. B004TST

      Attach the claw and install the tube clamp.

  37. INSTALL FRONT SEAT HEADREST INSERT SUB-ASSEMBLY LH (for Power Headrest)

    Click here

  38. INSTALL FRONT SEATBACK BEZEL


    1. B004VI8C01
      B004RMI Install in this Direction

      Slide in the installation direction shown in the illustration, insert the guide and install the front seatback bezel.

    2. Install the 2 clips.

  39. INSTALL LUMBER SUPPORT PUMP SUB-ASSEMBLY LH

    Click here

  40. INSTALL FRONT SEAT SET BRACKET SUB-ASSEMBLY RH


    1. B004XUL

      Install the front seat set bracket sub-assembly RH with the clip.

  41. INSTALL FRONT SEAT SET BRACKET SUB-ASSEMBLY LH


    1. B004R69

      Install the front seat set bracket sub-assembly LH with the clip.

  42. INSTALL FRONT SEATBACK SUPPORT RH


    1. B004TV0

      Install the front seatback support RH with the 2 screws.

  43. INSTALL FRONT NO. 2 SEATBACK SUPPORT RH (w/ Seatback Side Support)


    1. B004RN5

      Install the front No. 2 seatback support RH with the 2 nuts.

      Torque:
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }
    2. B004WMNC01
      *a Yellow Tube Color

      Attach the claw and connect the joint.

  44. INSTALL FRONT NO. 3 SEATBACK SUPPORT LH (w/ Seatback Side Support)


    1. B004SOK

      Install the front No. 3 seatback support LH with the 2 nuts.

      Torque:
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }
    2. B004UA4C01
      *a Yellow Tube Color

      Attach the claw and connect the joint.

  45. INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


    1. B004U83C01
      B004RMI Install in this Direction

      Align the guide and install the seatback climate control blower LH with the 3 screws.

    2. Attach the claw and install the connector.

  46. INSTALL FRONT NO. 2 SEAT WIRE LH


    1. B004SFHC01
      *A w/ Refresh Seat

      Attach the wire harness clamp and install the front No. 2 seat wire LH.

    2. w/o Refresh Seat:


      1. Connect the 6 connectors.

    3. w/ Refresh Seat:


      1. Connect the 7 connectors.

    4. B004XPZ

      for Manual Headrest:


      1. Connect the 4 connectors.

  47. INSTALL FRONT NO. 2 SEAT WIRE RH


    1. B004V53C01
      *A w/ Refresh Seat

      Attach the wire harness clamp and install the front No. 2 seat wire RH.

    2. w/o Refresh Seat:


      1. Connect the 6 connectors.

    3. w/ Refresh Seat:


      1. Connect the 7 connectors.

    4. B004UM3

      for Manual Headrest:


      1. Connect the 4 connectors.

  48. INSTALL SEAT AUDIO WIRE (w/ Rear Seat Entertainment System)


    1. B004XXUC01
      *a Guide
      *b Wire Harness Clamp

      Attach the wire harness clamp.

    2. Align the guide and install the seat audio wire with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  49. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH (for Sports Seat Type)

    Click here

  50. INSTALL SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004T0KC01
      B004RMI Install in this Direction

      Attach the hook and install the seatback main stretcher cushion assembly.

    2. B004TOQC01
      *a Clear Tube Color
      *b Blue Tube Color
      *c Green Tube Color
      *d Yellow Tube Color
      *e Orange Tube Color

      Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type front seatback pad.

  51. INSTALL SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004UT0C01
      B004RMI Install in this Direction

      Attach the hook and install the seatback main stretcher cushion assembly.

    2. B004RYQC01
      *a Clear Tube Color
      *b Blue Tube Color
      *c Green Tube Color
      *d Yellow Tube Color
      *e Orange Tube Color

      Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type front seatback pad.

  52. INSTALL SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. w/ Front Passenger Side Folding Headrest:


      1. B004RDUC01
        B004RMI Install in this Direction

        Attach the hook and install the seatback main stretcher cushion assembly.

      2. B004XJNC01
        *a Blue Tube Color
        *b Green Tube Color
        *c Yellow Tube Color
        *d Orange Tube Color

        Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type front seatback pad.

  53. INSTALL SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. w/ Front Passenger Side Folding Headrest:


      1. B004T6QC01
        B004RMI Install in this Direction

        Attach the hook and install the seatback main stretcher cushion assembly.

      2. B004VBUC01
        *a Blue Tube Color
        *b Green Tube Color
        *c Yellow Tube Color
        *d Orange Tube Color

        Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type front seatback pad.

  54. INSTALL FRONT SEATBACK PAD C (w/ Refresh Seat)


    1. Clean double-sided tape installation surface


      1. When reusing the separate type front seatback pad, remove the double-sided tape remaining on the installation surface.

    2. Remove the peeling paper from the face of the front seatback pad C.

      Tech Tips

      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. B004UTBC02
      B004TUP Double-sided Tape

      Install the front seatback pad C to the position shown in the illustration.

      Tech Tips

      Install so that the front seatback pad C fits within the mark-off line on the separate type front seatback pad LH.

      B004UQNC01
      *a Pad Mark-off Line

  55. INSTALL SEAT COVER WIRE


    1. B004SY7N01

      Install the seat cover wire.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.

      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.

      • Make sure to read the precautions before preparing the wire.

        Click here

      Dimensions
      A 110 mm (4.33 in.)
      B 170 mm (6.69 in.)
      C 200 mm (7.87 in.)

      Tech Tips

      The dimensions shown in the illustration are the length.

      B004V9X

  56. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

    Tech Tips

    When installing a separate type front seatback cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B004TV1

      except Front Passenger Side Folding Headrest:


      1. Insert the guide and install the headrest base.

    2. B004U2EC01
      *a Hog Ring Pliers

      for Standard Seat Type:


      1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 10 new hog rings in the order indicated in the illustration.

        Note


        • Be careful not to damage the separate type front seatback cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    3. B004T6PC02
      *a Fastening Tape
      *b Hog Ring Pliers

      for Sports Seat Type:


      1. Attach the fastening tape.

      2. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 10 new hog rings in the order indicated in the illustration.

        Note


        • Be careful not to damage the separate type front seatback cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    4. B004Y3TC01
      *a Fastening Tape
      *b Hog Ring Pliers

      w/ Front Passenger Side Folding Headrest:


      1. Pull out the strap of the separate type front seatback cover out of the hole of the separate type front seat cushion pad and attach the fastening tape.

      2. Using hog ring pliers, install 6 new hog rings securely.

        Note


        • Be careful not to damage the separate type front seatback cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    5. except Front Passenger Side Folding Headrest:


      1. B004WVXC01
        *a Hog Ring Pliers

        Pull out the strap of the separate type front seatback cover out of the hole of the separate type front seat cushion pad.

      2. Using hog ring pliers, install 4 new hog rings securely.

        Note


        • Be careful not to damage the separate type front seatback cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

  57. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Set the separate type front seatback cover with pad.

    2. w/ Refresh Seat:


      1. B004U98

        Pass the tube out through the hole in the lumbar support adjuster assembly.

    3. for Standard Seat Type:


      1. B004WR1C01
        B004RMI Install in this Direction

        Temporarily install the front seat airbag assembly LH.

      2. Attach the wire harness clamp.

      3. Install the front seat airbag assembly LH with the 2 new nuts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    4. B004TUYC01
      B004RMI Install in this Direction

      for Sports Seat Type:


      1. Install the bracket of the separate type front seatback cover with a new nut.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    5. w/ Refresh Seat:


      1. Attach the claw and connect the joint.

        B004SLGC01
        *a Orange Tube Color *b Yellow Tube Color
        *c Blue Tube Color *d Green Tube Color
        *e Clear Tube Color - -
    6. B004WVJ

      Install the 4 clips.

    7. B004V06C02
      *A w/ Rear Seat Entertainment System
      *a Connector Clamp
      *b Wire Harness Clamp

      w/ Rear Seat Entertainment System:


      1. Attach the wire harness clamp.

    8. Attach the connector clamp.

    9. B004SHM

      Install the 3 clips.

    10. w/ Rear Seat Entertainment System:


      1. B004W4H

        Install the 5 clips.

    11. B004YVKC01
      *A w/ Seat Heater System
      *a Wire Harness Clamp
      *b Hook

      Attach the hook.

    12. w/ Seat Heater System:


      1. Attach the wire harness clamp of the seatback heater.

    13. except Front Passenger Side Folding Headrest:


      1. B004YP5

        Install the 2 screws.

  58. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    1. B004VBH

      Align the guide and temporarily install the front seatback assembly to the separate type front seat cushion assembly.

    2. B004TR0

      Install the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. B004YUI

      Attach the hook.

    4. B004XUWC01
      *A w/ Refresh Seat
      *B w/ Seat Cushion Side Support
      *C w/ Seat Cushion Pelvic Support

      w/ Refresh Seat, Seat Cushion Side Support, Seat Cushion Pelvic Support:


      1. Attach the claw and connect the joint.

      2. Attach the tube clamp and install the tube.

    5. B004S8MC01
      B004RMI Install in this Direction

      w/ Rear Seat Entertainment System:


      1. Attach the claw and install the connector.

      2. Attach the wire harness clamp and install the seat audio wire.

    6. B004TTV

      w/ Seat Heater System:


      1. Attach the wire harness clamp and connect the seatback heater connector.

    7. B004XTZC02
      B004RMI Install in this Direction

      Attach the claw and install the connector.

    8. Attach the wire harness clamp and install the wire harness of the front seat airbag assembly LH.

    9. B004XV3

      Attach the wire harness clamp and connect the 2 front No. 2 seat wire LH connectors.

  59. INSTALL FRONT SEAT HEADREST SUPPORT (for Manual Headrest)


    1. B004X2DC01
      B004RMI Install in this Direction

      Attach the claw and install the 2 front seat headrest supports.

  60. INSTALL FRONT SEATBACK BOARD (except Front Passenger Side Folding Headrest)


    1. B004RDOC01
      B004RMI Install in this Direction

      Attach the claws and clips and install the front seatback board.

  61. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. B004VICC01
      B004RMI Install in this Direction

      for Power Headrest:


      1. Attach the pin and install the front seat headrest assembly.

    2. for Manual Headrest:


      1. Install the front seat headrest assembly.

  62. INSTALL FRONT SEAT FRONT CUSHION SHIELD LH


    1. B004VJOC01
      *a Clip A
      *b Clip B
      B004RMI Install in this Direction

      Insert the guide and install the front seat front cushion shield LH.

    2. Attach the clip A.

    3. Install the clip B.

  63. INSTALL FRONT INNER SEAT CUSHION SHIELD LH


    1. B004UBMC01
      B004RMI Install in this Direction

      Install the strap of the separate type front seat cushion cover to the front inner seat cushion shield LH.

    2. B004W0Y

      Attach the claw.

    3. B004URT

      Insert the guide and attach the claw.

    4. B004S53

      Attach the claw and install the front inner seat cushion shield LH.

  64. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. B004XMP

      Attach the claw.

    2. B004WGUC01
      B004RMI Install in this Direction

      Slide in the installation direction shown in the illustration and attach the claw.

    3. B004UUD

      Insert the guide and attach the claw.

    4. B004T5P

      Attach the claw and install the front seat cushion shield LH.

  65. INSTALL FRONT SEATBACK PANEL A (w/o Rear Seat Entertainment System)


    1. B004UN9C01
      B004RMI Install in this Direction

      Install the front seatback panel A with the 5 screws.

  66. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. B004VUJC01
      B004RMI Install in this Direction

      Lift up in the installation direction shown in the illustration to attach the hook.

    2. w/ Rear Seat Entertainment System:


      1. B004R73

        Install the wire harness to the clamp.

      2. Install the 2 clips.

    3. B004YLQ

      Install the front seatback board sub-assembly LH with the 2 screws.

    4. B004RINC01
      B004RMI Install in this Direction

      Insert the front seatback board sub-assembly LH in the direction of the arrow shown in the illustration.

    5. B004XAA

      Attach the hooks and connect the rubber band of the front seatback board sub-assembly LH.

  67. INSTALL FRONT POWER SEAT SWITCH ASSEMBLY LH

    Click here

  68. INSTALL BEZEL SWITCH HOLE COVER


    1. B004SIX

      Align the guide and install the bezel switch hole cover with the 3 screws.

  69. INSTALL SEAT ADJUSTER SHIELD CLAMP BRACKET LH


    1. B004UZU

      Align the guides and install the seat adjuster shield clamp bracket LH with the 2 screws.

  70. INSTALL FRONT POWER ADJUSTER SHIELD LH


    1. B004UCM

      Connect the connector and install the wire harness clamp.

    2. B004XFAC01
      *a Clip A
      *b Clip B
      *c Clip C
      B004RMI Install in this Direction (1)
      B004T3S Install in this Direction (2)

      Push in the installation direction (1) to insert the guide and attach the clip A.

    3. Push in the installation direction (2) to attach clip B and clip C and install the front power adjuster shield LH.

  71. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. B004VVBC01
      B004RMI Install in this Direction

      Attach the claw and install the reclining power seat switch knob.

  72. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. B004Y84C01
      B004RMI Install in this Direction

      Attach the claw and install the slide and vertical power seat switch knob.

  73. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  74. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  75. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here