FRONT SEAT ASSEMBLY DISASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • This may result in injury.

B004YMT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  2. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here

  3. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  4. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. B004WW0C01
      B004RMI Remove in this Direction

      Using moulding remover A, detach the claw and remove the slide and vertical power seat switch knob.

  5. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. B004REOC01
      B004RMI Remove in this Direction

      Using moulding remover A, detach the claw and remove the reclining power seat switch knob.

  6. REMOVE FRONT POWER ADJUSTER SHIELD LH


    1. B004TGRC01
      *a Clip A
      *b Clip B
      *c Clip C
      B004V32 Place Hand Here
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Place your hand at the position shown in the illustration and pull in the removal direction (1) to detach clip A and clip B.

    2. Place your hand in the position shown in the illustration and slide in the removal direction (2) to detach the guide and clip C.

    3. B004UCM

      Remove the wire harness from the clamp.

    4. Disconnect the connector and remove the front power seat switch assembly LH together with the front power adjuster shield LH.

  7. REMOVE SEAT ADJUSTER SHIELD CLAMP BRACKET LH


    1. B004UZU

      Remove the 2 screws.

    2. Detach the guides and seat adjuster shield clamp bracket LH.

  8. REMOVE BEZEL SWITCH HOLE COVER


    1. B004SIX

      Remove the 3 screws.

    2. Detach the guide and remove the front power seat switch assembly LH together with the bezel switch hole cover.

  9. REMOVE FRONT POWER SEAT SWITCH ASSEMBLY LH

    Click here

  10. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. B004XAA

      Detach the hook and disconnect the rubber band of the front seatback board sub-assembly LH.

    2. B004Y7QC01
      B004RMI Remove in this Direction

      Fold back the front seatback board sub-assembly LH in the direction of the arrow shown in the illustration.

    3. B004YLQ

      Remove the 2 screws.

    4. w/ Rear Seat Entertainment System:


      1. B004UTY

        Using a clip remover, remove the 2 clips.

      2. Remove the wire harness from the clamp.

    5. B004UR2C01
      B004RMI Remove in this Direction

      While pulling in the removal direction shown in the illustration to detach the guide and remove the front seatback board sub-assembly LH.

  11. REMOVE FRONT SEATBACK PANEL A (w/o Rear Seat Entertainment System)


    1. B004RHJC01
      B004RMI Remove in this Direction

      Remove the 5 screws and front seatback panel A.

  12. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. B004UYUC01
      B004VGX Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, detach the claw.

    2. B004VJ1

      Using moulding remover A, detach the claw and guide.

    3. B004R2DC01
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and slide the front seat cushion shield LH in the removal direction shown in the illustration.

    4. B004Y0TC01
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the front seat cushion shield LH.

  13. REMOVE FRONT INNER SEAT CUSHION SHIELD LH


    1. B004SYLC01
      B004VGX Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, detach the claw.

    2. B004T4I

      Using moulding remover A, detach the claw and guide.

    3. B004YKMC01
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped in protective tape, detach the claw.

    4. B004Y6PC01
      B004RMI Remove in this Direction

      Detach the strap of the separate type front seat cushion cover and remove the front inner seat cushion shield LH.

  14. REMOVE FRONT SEAT FRONT CUSHION SHIELD LH


    1. B004YICC01
      *a Clip A
      *b Clip B
      B004RMI Remove in this Direction

      Using a clip remover, detach clip A.

    2. Using a clip remover, remove clip B.

    3. Pull in the removal direction shown in the illustration to detach the guide and remove the front seat front cushion shield LH.

  15. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. B004TBNC01
      B004RMI Remove in this Direction

      for Power Headrest:

      Lift up the pin and detach it to remove the front seat headrest assembly.

    2. for Manual Headrest:

      Remove the front seat headrest assembly.

  16. REMOVE FRONT SEATBACK BOARD (except Front Passenger Side Folding Headrest)


    1. B004V0DC01
      B004RMI Remove in this Direction

      Using moulding remover B, detach the clip.

    2. Detach the claw and remove front seatback board.

  17. REMOVE FRONT SEAT HEADREST SUPPORT (for Manual Headrest)


    1. B004TIJ

      Detach the claw.

    2. B004WK1C01
      B004RMI Remove in this Direction

      Remove the 2 front seat headrest supports.

  18. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    1. B004XV3

      Disconnect the 2 front No. 2 seat wire LH connectors and remove the wire harness clamp.

    2. B004RIQC01
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Detach the wire harness clamp.

    3. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the wire harness of the front seat airbag assembly LH.

    4. B004TTV

      w/ Seat Heater System:


      1. Disconnect seatback heater connector and detach the wire harness clamp.

    5. B004TRYC01
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      w/ Rear Seat Entertainment System:


      1. Detach the wire harness clamp.

      2. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the seat audio wire.

    6. B004TI4C01
      *A w/ Refresh Seat
      *B w/ Seat Cushion Side Support
      *C w/ Seat Cushion Pelvic Support
      B004VGX Protective Tape

      w/ Refresh Seat, Seat Cushion Side Support, Seat Cushion Pelvic Support:


      1. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

      2. Detach the tube clamp and remove the tube.

    7. B004YUI

      Detach the hook.

    8. B004TR0

      Remove the 4 bolts.

    9. B004RHCC01
      B004VGX Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, detach the guide and remove the separate type front seatback assembly.

  19. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. except Front Passenger Side Folding Headrest:


      1. B004YP5

        Remove the 2 screws.

    2. B004YVKC01
      *A w/ Seat Heater System
      *a Wire Harness Clamp
      *b Hook

      w/ Seat Heater System:


      1. Detach the wire harness clamp of the seatback heater.

    3. Detach the hook.

    4. B004SHM

      Using a clip remover, remove the 3 clips.

    5. w/ Rear Seat Entertainment System:


      1. B004W4H

        Using a clip remover, remove the 5 clips.

    6. B004V06C01
      *A w/ Rear Seat Entertainment System
      *a Connector Clamp
      *b Wire Harness Clamp

      Detach the connector clamp.

    7. w/ Rear Seat Entertainment System:


      1. Detach the wire harness clamp.

    8. B004WVJ

      Using a clip remover, remove the 4 clips.

    9. w/ Refresh Seat:


      1. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

        B004SMEC01
        *a Orange Tube Color *b Yellow Tube Color
        *c Blue Tube Color *d Green Tube Color
        *e Clear Tube Color - -
        B004VGX Protective Tape - -

    10. for Standard Seat Type:


      1. B004REGC01
        B004RMI Remove in this Direction

        Remove the 2 nuts.

      2. Detach the wire harness clamp.

      3. Pull in the removal direction shown in the illustration to remove the front seat airbag assembly LH.

    11. B004RNE

      for Sports Seat Type:


      1. Remove the nut and bracket of the separate type front seatback cover.

    12. w/ Refresh Seat:


      1. B004VO9

        Pull the tube out through the hole in the lumbar support adjuster assembly LH.

    13. Remove the separate type front seatback cover with pad.

  20. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. except Front Passenger Side Folding Headrest:


      1. B004SMQ

        Remove the 4 hog rings and pull out the strap.

    2. B004TANC01
      *a Fastening Tape

      w/ Front Passenger Side Folding Headrest:


      1. Remove the 6 hog rings.

      2. Detach the fastening tape and pull out the strap.

    3. B004UH3

      for Standard Seat Type:


      1. Remove the 10 hog rings and separate type front seatback cover.

    4. B004X9YC01
      *a Fastening Tape

      for Sports Seat Type:


      1. Remove the 10 hog rings.

      2. Detach the fastening tape and remove the separate type front seatback cover.

    5. B004TV1

      except Front Passenger Side Folding Headrest:


      1. Detach the guide and remove the headrest base.

  21. REMOVE SEAT COVER WIRE


    1. B004SY7

      Remove the seat cover wire.

  22. REMOVE FRONT SEATBACK PAD C (w/ Refresh Seat)


    1. B004UTBC01
      B004TUP Double-sided Tape

      Remove the double-sided tape and front seatback pad C.

  23. REMOVE SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004SY0

      Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type front seatback pad.

    2. B004T9VC01
      B004RMI Remove in this Direction

      Detach the hook and remove the seatback main stretcher cushion assembly.

  24. REMOVE SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004U4A

      Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type front seatback pad.

    2. B004TTEC01
      B004RMI Remove in this Direction

      Detach the hook and remove the seatback main stretcher cushion assembly.

  25. REMOVE SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. w/ Front Passenger Side Folding Headrest:


      1. B004X1V

        Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type front seatback pad.

      2. B004WDFC01
        B004RMI Remove in this Direction

        Detach the hook and remove the seatback main stretcher cushion assembly.

  26. REMOVE SEATBACK MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. w/ Front Passenger Side Folding Headrest:


      1. B004V7I

        Pull out the tube of the seatback main stretcher cushion assembly from the hole of the separate type front seatback pad.

      2. B004YG9C01
        B004RMI Remove in this Direction

        Detach the hook and remove the seatback main stretcher cushion assembly.

  27. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH (for Sports Seat Type)

    Click here

  28. REMOVE SEAT AUDIO WIRE (w/ Rear Seat Entertainment System)


    1. B004XXUC01
      *a Guide
      *b Wire Harness Clamp

      Remove the bolt.

    2. Detach the guide and wire harness clamp and remove the seat audio wire.

  29. REMOVE FRONT NO. 2 SEAT WIRE LH


    1. B004SFHC01
      *A w/ Refresh Seat

      w/o Refresh Seat:


      1. Disconnect the 6 connectors.

    2. w/ Refresh Seat:


      1. Disconnect the 7 connectors.

    3. B004XPZ

      for Manual Headrest:


      1. Disconnect the 4 connectors.

    4. Detach the wire harness clamp and remove the front No. 2 seat wire LH.

  30. REMOVE FRONT NO. 2 SEAT WIRE RH


    1. B004V53C01
      *A w/ Refresh Seat

      w/o Refresh Seat:


      1. Disconnect the 6 connectors.

    2. w/ Refresh Seat:


      1. Disconnect the 7 connectors.

    3. B004UM3

      for Manual Headrest:


      1. Disconnect the 4 connectors.

    4. Detach the wire harness clamp and remove the front No. 2 seat wire RH.

  31. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


    1. B004SECC01
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the connector.

    2. Remove the 3 screws.

    3. Detach the guide and remove the seatback climate control blower LH.

  32. REMOVE FRONT NO. 2 SEATBACK SUPPORT LH (w/ Seatback Side Support)


    1. B004UVRC01
      *a Yellow Tube Color
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

    2. B004RN5

      Remove the 2 nuts and front No. 2 seatback support LH.

  33. REMOVE FRONT NO. 3 SEATBACK SUPPORT LH (w/ Seatback Side Support)


    1. B004SG0C01
      *a Yellow Tube Color
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

    2. B004SOK

      Remove the 2 nuts and front No. 3 seatback support LH.

  34. REMOVE FRONT SEATBACK SUPPORT RH


    1. B004TV0

      Remove the 2 screws and front seatback support RH.

  35. REMOVE FRONT SEAT SET BRACKET SUB-ASSEMBLY LH


    1. B004R69

      Using a clip remover, remove the clip and front seat set bracket sub-assembly LH.

  36. REMOVE FRONT SEAT SET BRACKET SUB-ASSEMBLY RH


    1. B004XUL

      Using a clip remover, remove the clip and front seat set bracket sub-assembly RH.

  37. REMOVE LUMBER SUPPORT PUMP SUB-ASSEMBLY LH

    Click here

  38. REMOVE FRONT SEATBACK BEZEL


    1. B004WY0C01
      B004RMI Remove in this Direction

      Using a clip remover, remove the 2 clips.

    2. Slide in the removal direction shown in the illustration to detach the guide and remove the front seatback bezel.

  39. REMOVE FRONT SEAT HEADREST INSERT SUB-ASSEMBLY LH (for Power Headrest)

    Click here

  40. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Note

    When servicing, always hold the lumbar base and do not hold only the tube and joint areas.


    1. B004TST

      Detach the claw and the tube clamp.

    2. While pulling in the removal direction (1) shown in the illustration to pull the tube out through the hole.

      B004R4BC01
      *a Lumbar Base - -
      B004RMI Remove in this Direction (1) B004T3S Remove in this Direction (2)

    3. Pull down in the removal direction (2) shown in the illustration to remove the lumbar support adjuster assembly LH.

  41. REMOVE FRONT SEATBACK EDGE PROTECTOR

    Tech Tips

    Use the same procedure for the other locations.


    1. B004SGCC01
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped in protective tape, detach the claw.

    2. B004Y2OC01
      B004RMI Remove in this Direction

      Remove the front seatback edge protector.

  42. REMOVE FRONT SEATBACK HOOK


    1. B004S3MC01
      B004RMI Remove in this Direction

      Detach the claw and remove the 2 front seatback hooks.

  43. REMOVE FRONT SEATBACK BEZEL


    1. B004V72C01
      B004RMI Remove in this Direction

      Detach the claw and remove the No. 3 interior illumination light assembly together with the front seatback bezel.

  44. REMOVE NO. 3 INTERIOR ILLUMINATION LIGHT ASSEMBLY


    1. B004WFRC01
      B004RMI Remove in this Direction

      Detach the claw and remove the No. 3 interior illumination light assembly from the front seatback bezel.

  45. REMOVE SEAT CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Note

    Perform work with the reclining adjuster inside cover on top of a box to prevent it from becoming damaged.

    B004WUB

    1. B004THQC01
      B004SZX Joint
      B004UK4 Screw
      B004XCB Connector
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

    2. Disconnect the connector.

    3. Remove the 3 screws.

    4. Detach the tube clamp and remove the seat check valve with hose LH.

  46. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. B004T28

      Disconnect the connector of the front vertical motor.

    2. B004TOTC33
      *a

      Component without harness connected

      (Front Vertical Motor (Front Seat Adjuster Assembly))

      Connect the No. 1 terminal of the front vertical motor to the positive (+) auxiliary battery terminal, and the No. 4 terminal to the negative (-) auxiliary battery terminal and then raise the cushion height to the uppermost position.

    3. B004TLG

      Disconnect the connector of the rear lifter motor.

    4. B004TOTC33
      *a

      Component without harness connected

      (Rear Lifter Motor (Front Seat Adjuster Assembly))

      Connect the No. 1 terminal of the rear lifter motor to the positive (+) auxiliary battery terminal, and the No. 4 terminal to the negative (-) auxiliary battery terminal and then raise the cushion height to the uppermost position.

    5. w/ Ottoman:


      1. B004UJS

        Disconnect the connector of the ottoman motor.

      2. B004TOTC33
        *a

        Component without harness connected

        (Ottoman Motor (Front Seat Adjuster Assembly))

        Connect the No. 1 terminal of the ottoman motor to the positive (+) auxiliary battery terminal, and the No. 4 terminal to the negative (-) auxiliary battery terminal and then adjust the length of the cushion to the frontmost position.

    6. B004T6M

      w/ Seat Heater System:


      1. Detach the seat cushion heater clamp and disconnect the connector.

    7. for Front Passenger Side without Occupant Classification System:


      1. B004UC8

        Disconnect the connector of the occupant detection sensor.

      2. B004XH7C01
        B004RMI Remove in this Direction
        B004VGX Protective Tape

        Using a thin-bladed screwdriver wrapped with protective tape, detach the claw and disconnect the connector of the occupant detection sensor.

    8. w/ Ottoman:


      1. Detach the hook.

        B004SGBC01
        B004TUP Fastening Tape - -

      2. Using s clip remover, detach the clip.

      3. Detach the fastening tape and open the separate type front seat cushion cover.

      4. Detach the hook.

        B004RHR

      5. Using a clip remover, detach the clip.

    9. w/o Ottoman:


      1. Detach the hook.

        B004RNA

      2. Using a clip remover, detach the clip.

    10. Remove the separate type front seat cushion cover with pad.

  47. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. B004UPTC01
      *a Band
      *b Strap

      Pull the band of the separate type front seat cushion cover out from the separate type front seat cushion pad.

    2. Remove the 4 hog rings and pull out the strap from the hole of the separate type front seat cushion pad.

    3. B004XHK

      Remove the 8 hog rings and separate type front seat cushion cover.

  48. REMOVE SEAT COVER WIRE


    1. B004RS1

      Remove the seat cover wire.

  49. REMOVE FRONT SEAT CUSHION COVER MAIN PAD LH (w/ Refresh Seat)


    1. Remove the 2 hog rings and pull out the strap from the hole of the separate type front seat cushion pad.

      B004YTCC01
      B004TUP Double-sided Tape - -

    2. Remove the 4 hog rings.

    3. Remove the double-sided tape and front seat cushion cover main pad LH.

  50. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004RUJ

      Pull out the tube of the seat cushion main stretcher cushion assembly from the hole and strap of the separate type front seat cushion pad.

    2. B004XYOC01
      B004RMI Remove in this Direction

      Detach the hook and remove the seat cushion main stretcher cushion assembly.

  51. REMOVE SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B004UT2

      Pull out the tube of the seat cushion main stretcher cushion assembly from the hole and strap of the separate type front seat cushion pad.

    2. B004XHCC01
      B004RMI Remove in this Direction

      Detach the hook and remove the seat cushion main stretcher cushion assembly.

  52. REMOVE SEAT RECLINING ADJUSTER INSIDE COVER LH


    1. B004VLCC01
      *a Tube Clamp
      *b Clamp
      B004RMI Remove in this Direction

      w/ Seat Cushion Side Support:


      1. Remove the tube from the clamp.

    2. Pull in the removal direction shown in the illustration to detach the claw and clamp and remove the seat reclining adjuster inside cover LH.

  53. REMOVE SEAT RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the seat reclining adjuster inside cover LH.

  54. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH


    1. B004UWBC01
      *a Hook
      *b Guide
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)
      B004U7U Remove in this Direction (3)
      B004VGX Protective Tape

      Detach the hook.

    2. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw.

    3. Slide in the removal direction (3) shown in the illustration to detach the guide and remove the front lower seat cushion shield LH.

  55. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH


    1. B004R6OC01
      *a Hook
      *b Guide
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)
      B004U7U Remove in this Direction (3)
      B004VGX Protective Tape

      Detach the hook.

    2. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw.

    3. Slide in the removal direction (3) shown in the illustration to detach the guide and remove the front lower seat cushion shield RH.

  56. REMOVE OUTER SEAT SUPPORT LH


    1. B004VFK

      w/ Seat Cushion Side Support:


      1. Remove the 2 screws and outer seat support LH.

    2. B004RVI

      w/o Seat Cushion Side Support:


      1. Remove the 2 screws and outer seat support LH.

  57. REMOVE INNER SEAT SUPPORT LH


    1. B004XMN

      w/ Seat Cushion Side Support:


      1. Detach the tube clamp.

      2. Remove the 2 screws and inner seat support LH.

    2. B004VUI

      w/o Seat Cushion Side Support:


      1. Remove the 2 screws and inner seat support LH.

  58. REMOVE FRONT SEAT ADJUSTER SUB-ASSEMBLY LH (w/ Seat Cushion Pelvic Support)


    1. B004VDKC01
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the joint.

    2. Slide in the removal direction shown in the illustration to detach the hook and remove the front seat adjuster LH.

  59. REMOVE FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH


    1. B004VUCC01
      *a Wire Harness Clamp
      *b Hook A
      *c Hook B
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Detach the wire harness clamp.

    2. Pull up in the removal direction (1) shown in the illustration to detach hook A.

    3. Slide in the removal direction (2) shown in the illustration to detach hook B and remove the front seat cushion spring sub-assembly LH.

  60. REMOVE FRONT SEAT CUSHION WIRE HARNESS HOLDER LH


    1. w/ Ottoman:


      1. Disconnect the 2 connectors.

        B004SIJC01
        *A w/ Ottoman - -

    2. w/o Ottoman:


      1. Disconnect the connector.

    3. Detach the wire harness clamp.

    4. B004S5TC02
      B004RMI Removal in this Direction

      Remove the 3 screws and detach the claw.

    5. Slide in the removal direction shown in the illustration to remove the front seat wire LH together with the front seat cushion wire harness holder LH.

  61. REMOVE FRONT SEAT CUSHION WIRE HARNESS HOLDER RH (for Front Passenger Side)


    1. w/ Climate Control Seat System:


      1. Disconnect the 2 connectors.

        B004RMCC01
        *A w/ Climate Control Seat System *B w/o Ottoman
        *C w/ Ottoman - -

      2. Detach the wire harness clamp.

    2. B004R89

      w/ Occupant Classification System:


      1. Detach the wire harness clamp.

      2. Disconnect the 2 connectors.

      3. Detach the wire harness clamp.

    3. B004T41C01
      B004RMI Removal in this Direction

      Remove the 3 screws and detach the claw.

    4. Slide in the removal direction shown in the illustration to remove the front seat wire RH together with the front seat cushion wire harness holder RH.

  62. REMOVE FRONT SEAT WIRE RH (for Front Passenger Side with Occupant Classification System)


    1. B004X7P

      Disconnect the 2 connector.

    2. Detach the wire harness clamp.

    3. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the front seat wire RH.

  63. REMOVE FRONT SEAT WIRE LH


    1. B004RNWC01
      *A w/ Seat Heater System
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      w/o Seat Heater System:


      1. Disconnect the 4 connectors.

    2. w/ Seat Heater System:


      1. Disconnect the 5 connectors.

    3. Detach the wire harness clamp.

    4. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the connector.

    5. Detach the claw and remove the front seat wire LH.

  64. REMOVE POSITION CONTROL ECU ASSEMBLY

    Click here

  65. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


    1. B004UNFC01
      B004RMI Remove in this Direction

      Detach the claw and disconnect the seat heater control sub-assembly LH.

  66. REMOVE OCCUPANT DETECTION ECU (for Front Passenger Side with Occupant Classification System)

    Click here

  67. REMOVE SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY LH (w/ Climate Control Seat System)


    1. B004SM8C01
      *a Guide
      *b Clamp
      B004RMI Remove in this Direction

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the connector.

    2. Remove the 2 bolts.

    3. Detach the guide.

    4. Pull in the removal direction shown in the illustration to detach the clamp and remove the seat cushion climate control blower assembly LH.

  68. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH


    1. B004WUGC01
      B004RMI Remove in this Direction (1)
      B004T3S Remove in this Direction (2)

      Pull in the removal direction (1) shown in the illustration to detach the claw.

    2. Pull in the removal direction (2) shown in the illustration to detach the guide and remove the front lower seat cushion shield LH.

  69. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH (w/ Front Passenger Side Folding Headrest)

    Tech Tips

    Use the same procedure described for the LH side.

  70. REMOVE REAR INNER SEAT TRACK BRACKET COVER LH (w/ Front Passenger Side Folding Headrest)


    1. B004T09C01
      *a Guide A
      *b Guide B
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, remove guide A.

    2. Slide in the removal direction shown in the illustration to detach the guide B.

    3. B004S60C01
      B004RMI Remove in this Direction

      Rotate in the removal direction shown in the illustration to remove the rear inner seat track bracket cover LH.

  71. REMOVE REAR OUTER SEAT TRACK BRACKET COVER RH (w/ Front Passenger Side Folding Headrest)

    Tech Tips

    Use the same procedure described for the rear inner seat track bracket cover LH.

  72. REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH (w/ Front Passenger Side Folding Headrest)


    1. B004V9AC01
      *a Guide A
      *b Guide B
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, remove guide A.

    2. Slide in the removal direction shown in the illustration, detach guide B and remove the front inner seat track bracket cover LH.

  73. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER RH (w/ Front Passenger Side Folding Headrest)

    Tech Tips

    Use the same procedure described for the front inner seat track bracket cover LH.

  74. REMOVE REAR UPPER SEAT TRACK COVER


    1. B004TSF

      Place a matchmark on the front seat adjuster assembly LH.

    2. B004RSS

      Connect the No. 1 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 4 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the rearmost position.

    3. B004YT6C01
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the rear upper seat track cover.

      Tech Tips

      Use the same procedure for the other locations.

  75. REMOVE UPPER SEAT TRACK RAIL COVER


    1. B004WVK

      Connect the No. 4 terminal of the slide motor to the positive (+) auxiliary battery terminal, and the No. 1 terminal to the negative (-) auxiliary battery terminal and then move the front seat adjuster assembly LH to the frontmost position.

    2. B004VP8C01
      B004RMI Remove in this Direction
      B004VGX Protective Tape

      Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the upper seat track rail cover.

      Tech Tips

      Use the same procedure for the other locations.