OCCUPANT CLASSIFICATION SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Occupant Detection / Data List.

    6. Read the Data List according to the display on the GTS.


      Body Electrical > Occupant Detection > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      FL Sensor Weight Information Front left sensor weight information

      Min.: -75.852 kg (-167.224 lb)

      Max.: 104.737 kg (230.903 lb)

      		 Current value displayed -
      RL Sensor Weight Information Rear left sensor weight information

      Min.: -75.852 kg (-167.224 lb)

      Max.: 104.737 kg (230.903 lb)

      		 Current value displayed -
      Total Weight Information Total weight information

      Min.: -151.704 kg (-334.447 lb)

      Max.: 209.475 kg (461.808 lb)

      		 Current value displayed -
      Weight Forward and Rearward Difference Weight difference between front and rear

      Min.: -180.589 kg (-398.127 lb)

      Max.: 180.589 kg (398.126 lb)

      		 Current value displayed -
      Airbag Total Weight Total weight information for airbag system

      Min.: -161.595 kg (-356.253 lb)

      Max.: 226.017 kg (498.277 lb)

      		 Current value displayed -
      Belt Warning Total Weight Total weight information for seat belt warning system

      Min.: -155.001 kg (-341.716 lb)

      Max.: 219.400 kg (483.689 lb)

      		 Current value displayed -
      VSC Status Vehicle speed status ON or OFF ON: Vehicle speed valid -
      VSC Vehicle Speed Vehicle speed

      Min.: 0.00 km/h (0.00 mph)

      Max.: 327.67 km/h (203.61 mph)

      		 Current value displayed -
      VSC Zero Point1 Zero point for acceleration sensor 1

      Min.: -4.5952 m/s2

      Max.: 4.5593 m/s2

      		Current value displayed -
      VSC Zero Point2 Zero point for acceleration sensor 2

      Min.: -4.5952 m/s2

      Max.: 4.5593 m/s2

      		Current value displayed -
      VSC Calibration Status Vehicle stability control calibration status Calibrated or Uncalibrated Calibrated -
      VSC Assembly Information Acceleration sensor assembly information Reverse Position or Normal Position Reverse Position or Normal Position Displays a fixed value for each vehicle.
      Yaw Rate/G Sensor Voltage Invalid Flag Yaw rate and acceleration sensor voltage invalid flag ON or OFF ON: Valid -
      Yaw Rate/G Sensor Malfunction Flag1 Malfunction flag for acceleration sensor 1 OK or NG OK -
      Yaw Rate/G Sensor Invalid Flag1 Invalid flag for acceleration sensor 1 ON or OFF ON: Valid -
      Yaw Rate/G Sensor Malfunction Flag2 Malfunction flag for acceleration sensor 2 OK or NG OK -
      Yaw Rate/G Sensor Invalid Flag2 Invalid flag for acceleration sensor 2 ON or OFF ON: Valid -
      Yaw Rate/G Sensor Assembly Information Acceleration sensor assembly information for occupant classification system Unset, Reverse Position or Normal Position Reverse Position or Normal Position

      • Displays a fixed value for each vehicle.

      • "Unset" will be displayed for approximately 2 seconds after the power switch is turned on (IG).
      Passenger Detection(Airbag) Passenger classification OFF/Child, CRS1, CRS2, AF05 or AM50

      OFF/Child: Vacant or child is seated

      CRS1: Child restraint system is installed

      CRS2: Child restraint system is installed

      AF05: Adult is seated

      AM50: Adult is seated

      		 -
      Passenger Detection(Belt Warning) Passenger detection for seat belt warning system OFF, Baggage or ON

      OFF: Seat is vacant

      Baggage: Seat is occupied by baggage

      ON: Seat is occupied

      		 -
      Driving Status Driving status Stop, Drive or Turn

      Stop: Vehicle is stopped

      Drive: Vehicle is being driven straight

      Turn: Vehicle is turning

      		 -
      Passenger Buckle SW Passenger side buckle switch NG, Set or Unset

      Set: Front passenger seat belt is fastened

      Unset: Front passenger seat belt is not fastened

      		 "NG" will be displayed immediately after the power switch is turned on.
      The Number of DTCs Number of DTC recorded Min.: 0, Max.: 255 Number of storedDTCs displayed The number displayed is the total current DTCs and history DTCs stored (excluding duplicates).