Click here

ENTRY AND START SYSTEM(for Start Function) New Key Registration Warning Message is not Displayed

Click here
Click here
DTC Code DTC Name
  New Key Registration Warning Message is not Displayed
Click here

DESCRIPTION

If the new key registration warning message is not displayed after an electrical key transmitter sub-assembly has been registered, there may be communication problem between the certification ECU (smart key ECU assembly) and combination meter assembly.

Click here

CAUTION / NOTICE / HINT

Note:

  • When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.

Click here

PROCEDURE


  1. Click here

    CHECK FOR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.

    5. Check for DTCs.


      1. Body Electrical > Entry&Start > Trouble Codes


      Result
      Result Proceed to
      DTCs are not output A
      DTCs are output B

  2. Click here

    READ VALUE USING GTS (FL DOOR COURTESY SWITCH)


    1. Enter the following menus: Body Electrical / Main Body / Data List.

    2. Read the Data List according to the display on the GTS.


      1. Body Electrical > Main Body > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        FR Door Courtesy SW Courtesy light switch RH signal ON or OFF

        ON: Front door RH open

        OFF: Front door RH closed

        		 for RHD
        FL Door Courtesy SW Courtesy light switch LH signal ON or OFF

        ON: Front door LH open

        OFF: Front door LH closed

        		 for LHD




      1. Body Electrical > Main Body > Data List
        Tester Display
        FR Door Courtesy SW
        FL Door Courtesy SW





      Result
      Result Proceed to
      On the GTS screen, ON or OFF is displayed accordingly. A
      On the GTS screen, ON or OFF is not displayed accordingly. B

  3. Click here

    CHECK METER / GAUGE SYSTEM


    1. With the electrical key transmitter sub-assembly in the vehicle and all of the doors closed, lock the doors using the entry lock function and check that the warning message is displayed on the multi-information display.

      Result
      Result Proceed to
      The warning message is displayed on the multi-information display. A
      The warning message is not displayed on the multi-information display. B

  4. Click here

    ADDITIONAL KEY REGISTRATION


    1. Clear all of the registered electrical key transmitter sub-assemblies except one and perform registration again.

      Tip:

      Refer to Service Bulletin.

      Result
      Proceed to
      NEXT

  5. Click here

    CHECK MULTI-INFORMATION DISPLAY


    1. With all of the doors closed, lock the doors using the entry lock function.

    2. Unlock the doors using the entry unlock function, open the driver door and check that the warning message is displayed on the multi-information display.

      Result
      Result Proceed to
      The warning message is displayed on the multi-information display. A
      The warning message is not displayed on the multi-information display. B

    • A

      END (10 DAYS MAY HAVE ELAPSED SINCE AN ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS REGISTERED)

    • B

      REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)