ENTRY AND START SYSTEM(for Start Function) OPERATION CHECK


  1. CHECK CUSTOMIZE PARAMETERS

    Note

    The operation check below is based on the non-customized initial condition of the vehicle.

    Click here

  2. CHECK PUSH-BUTTON START FUNCTION


    1. Check the push-button start function:


      1. Get into the vehicle while carrying the electrical key transmitter sub-assembly with the power switch off. With the shift state park (P), check that the key indicator display is displayed when the brake pedal is depressed. Check that the hybrid control system starts when the power switch is pressed after the key indicator display is displayed on the multi-information display.

      2. While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the power switch is pressed with the brake pedal released: off → on (ACC) → on (IG) → off.

      3. With the shift state park (P), check that the steering lock operates when a door is opened.

      4. B004RRUC01
        *a Inspection Point

        Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

        Note

        Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

          Click here

        • Perform this inspection for both inspection points.

      5. B004SKIC01
        *a Inspection Point

        Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

        Note

        Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box, in the door pocket, in the console or on the floor.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).

          Click here

        • Perform this inspection for both inspection points.

  3. CHECK POWER SOURCE MODE CHANGING FUNCTION


    1. Check the power switch.


      1. Check that the power source mode changes according to the chart below.

        Shift Position Brake Pedal Power Source Mode when Power Switch Pressed
        Park (P) selected Released Off → on (ACC) → on (IG) → off
        Park (P) selected Depressed Off → hybrid control system starts
        Park (P) selected Depressed On (ACC) → hybrid control system starts
        Park (P) selected Depressed On (IG) → hybrid control system starts
        Park (P) selected Released / Depressed On (READY) → off
        Park (P) not selected Released / Depressed On (ACC) → on (IG)
        Park (P) not selected Released / Depressed On (READY) → off
        Park (P) not selected Released / Depressed On (IG) → off

  4. CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION


    1. Check the transmitter battery saving mode function:


      1. Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.

      2. Check that the entry and start system does not operate while in transmitter battery saving mode.

        Tech Tips

        To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.

  5. CHECK ENTRY CANCEL FUNCTION


    1. Cancel the entry and start system and check that all the functions of the entry and start system no longer operate.

      Click here

      Tech Tips

      While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless function, and the hybrid control system can be started by holding the electrical key transmitter sub-assembly near the power switch.

  6. CHECK KEY DIAGNOSTIC MODE

    Click here