Click here

WIRELESS DOOR LOCK CONTROL SYSTEM TERMINALS OF ECU

Click here
Click here
Click here
  1. B004TKOC28
    *1 Main Body ECU (Multiplex Network Body ECU) - -

    CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      Click here

    2. Reconnect the instrument panel junction block assembly connectors.

    3. Measure the voltage and resistance according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      A-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
      A-30 (ACC) - Body ground - Input ACC power supply Power switch on (ACC) 11 to 14 V ACC SW
      Power switch off Below 1 V
      A-31 (BECU) - Body ground - Input Auxiliary battery power supply Power switch off 11 to 14 V -
      A-32 (IG) - Body ground - Input IG power supply Power switch on (IG) 11 to 14 V IG SW
      Power switch off Below 1 V

    4. Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

      Click here

    5. Measure the voltage and check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      5F-31 (BZR) - Body ground B - Body ground Output Wireless door lock buzzer output Active Test Wireless Buzzer on

      Pulse generation

      (frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)

      		 -
      Active Test Wireless Buzzer off Below 1 V
  2. B004YU6E13

    CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. Disconnect the G71 certification ECU (smart key ECU assembly) connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      G71-18 (E) - Body ground W-B - Body ground - Ground Always Below 1 Ω -
      G71-4 (+B) - Body ground W - Body ground Input Power supply Power switch off 11 to 14 V -

    3. Reconnect the G71 certification ECU (smart key ECU assembly) connector.

    4. Measure the voltage and check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
      L31-18 (RCO) - G71-18 (E) G - W-B Output

      Output to door control receiver

      (Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)

      Procedure:


      1. Power switch off

      2. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

      3. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      Pulse generation

      (See waveform 1)

      		 -
      L31-19 (RDAM) - G71-18 (E) BE - W-B Input

      Door control receiver verifies data received from electrical key transmitter sub-assembly.

      Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).

      Proceed:


      1. Power switch off

      2. All doors locked

      3. Electrical key transmitter sub-assembly not inside vehicle

      4. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

      5. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed

      Pulse generation

      (See waveform 2)

      		 -
      L31-20 (CSEL) - G71-18 (E) P - W-B Output Communication channel switching circuit

      Procedure:


      1. Power switch off

      2. All doors closed

      		 Below 1 V → pulse generation -
    5. B004VQAC12
      *a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
      *b After lock or unlock switch of electrical key transmitter sub-assembly pressed

      Using an oscilloscope, check waveform 1.

      Tip:

      The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

      Table 1. Waveform 1 (Reference)
      Item Content
      Tester Connection L31-18 (RCO) - G71-18 (E)
      Tool Setting 2 V/DIV., 500 ms/DIV.
      Condition
      1. Procedure:

      2. Power switch off

      3. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

      4. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed
    6. B004RTDC12
      *a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
      *b After lock or unlock switch of electrical key transmitter sub-assembly pressed

      Using an oscilloscope, check waveform 2.

      Tip:

      The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

      Table 2. Waveform 2 (Reference)
      Item Content
      Tester Connection L31-19 (RDAM) - G71-18 (E)
      Tool Setting 5 V/DIV., 500 ms/DIV.
      Condition
      1. Procedure:

      2. Power switch off

      3. All doors locked

      4. Electrical key transmitter sub-assembly not inside vehicle

      5. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

      6. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed