OUTER REAR VIEW MIRROR INSPECTION

PROCEDURE

1. Click here

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

   
   

   1. Check the operation of the retractable mirror.

      Note:
      

      • Disconnect and reconnect the auxiliary battery between each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      
      
      1. 

         *a	(A) Forward position
         *b	(B)
         *c	(C) Driving position
         *d	(D)
         *e	(E) Retracted position
         *f	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

         OK

         Tester Connection Condition Specified Condition z38-3 (MR) - Auxiliary battery positive (+) z38-11 (MF) - Auxiliary battery negative (-) Forward position (A) Moves from (A) to (E) z38-11 (MF) - Auxiliary battery positive (+) z38-3 (MR) - Auxiliary battery negative (-) Forward position (A) Does not move z38-3 (MR) - Auxiliary battery positive (+) z38-11 (MF) - Auxiliary battery negative (-) Position between forward position (A) and driving position (C) Moves from (B) to (E) z38-11 (MF) - Auxiliary battery positive (+) z38-3 (MR) - Auxiliary battery negative (-) Position between forward position (A) and driving position (C) Moves from (B) to (A) z38-3 (MR) - Auxiliary battery positive (+) z38-11 (MF) - Auxiliary battery negative (-) Driving position (C) Moves from (C) to (E) z38-11 (MF) - Auxiliary battery positive (+) z38-3 (MR) - Auxiliary battery negative (-) Driving position (C) Does not move z38-3 (MR) - Auxiliary battery positive (+) z38-11 (MF) - Auxiliary battery negative (-) Position between driving position (C) and retracted position (E) Moves from (D) to (E) z38-11 (MF) - Auxiliary battery positive (+) z38-3 (MR) - Auxiliary battery negative (-) Position between driving position (C) and retracted position (E) Moves from (D) to (C) z38-3 (MR) - Auxiliary battery positive (+) z38-11 (MF) - Auxiliary battery negative (-) Retracted position (E) Does not move z38-11 (MF) - Auxiliary battery positive (+) z38-3 (MR) - Auxiliary battery negative (-) Retracted position (E) Moves from (E) to (C)

         If the result is not as specified, replace the outer mirror actuator assembly LH.

   2. Check the operation of the mirror surface.

      
      
      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. Apply auxiliary battery voltage and check the operation of the mirror.

         OK

         Tester Connection Specified Condition z38-1 (MV) - Auxiliary battery positive (+) z38-10 (M+) - Auxiliary battery negative (-) Turns upward z38-10 (M+) - Auxiliary battery positive (+) z38-1 (MV) - Auxiliary battery negative (-) Turns downward z38-10 (M+) - Auxiliary battery positive (+) z38-9 (MH) - Auxiliary battery negative (-) Turns right z38-9 (MH) - Auxiliary battery positive (+) z38-10 (M+) - Auxiliary battery negative (-) Turns left

         If the result is not as specified, replace the outer mirror actuator assembly LH.

   3. Check the operation of the mirror heater.

      
      
      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

         Disconnect the outer rear view mirror assembly LH connector.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition z38-4 (HTR+) - z38-12 (HTR-) 25°C (75°F) 3.8 to 5.2 Ω

         If the result is not as specified, inspect the outer mirror LH or replace the outer mirror actuator assembly LH.

         Click here

      3. Connect the cable from the positive (+) auxiliary battery terminal to z38 terminal 4 (HTR+) and the negative (-) auxiliary battery terminal to z38 terminal 12 (HTR-), and then check that the mirror becomes warm.

         Tip:

         It takes a short time for the mirror to become warm.

         OK
         Mirror becomes warm.

         If the result is not as specified, inspect the outer mirror LH or replace the outer mirror actuator assembly LH.

         Click here

   4. 

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the side turn signal light assembly LH.

      
      

      1. Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

         OK
         Tester Connection Specified Condition z38-16 (B) - Auxiliary battery positive (+) z38-12 (-) - Auxiliary battery negative (-) Side turn signal light illuminates

         If the result is not as specified, inspect the side turn signal light assembly LH or replace the outer mirror actuator assembly LH.

         Click here

   5. Check the EC mirror operation.

      
      

      1. Connect a new 1.5 V dry-cell battery.

      2. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly LH)
         *b	Bright
         *c	Dark

         Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

         OK
         Tester Connection Specified Condition z38- 7 (EC+) - Positive (+) end of the 1.5 V dry-cell battery z38- 15 (EC-) - Negative (-) end of the 1.5 V dry-cell battery Mirror surface becomes dark

         Note:

         Do not apply a voltage of 1.5 V or higher.

         If the result is not as specified, inspect the outer mirror LH or replace the outer mirror actuator assembly LH.

         Click here

   6. 

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      w/ Blind Spot Monitor System:

      Check the operation of the blind spot monitor indicator.

      
      

      1. Connect 4 new 1.5 V dry-cell batteries in series.

      2. Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.

         OK
         Tester Connection Specified Condition z38- 8 (BSR+) - Positive (+) end of the 6 V dry-cell battery z38- 12 (-) - Negative (-) end of the 6 V dry-cell battery Blind spot monitor indicator comes on

         Note:

         Do not apply a voltage of 6 V or higher.

         If the result is not as specified, inspect the outer mirror LH or replace the outer mirror actuator assembly LH.

         Click here

2. Click here

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

   
   

   1. Check the operation of the retractable mirror.

      Note:
      

      • Disconnect and reconnect the auxiliary battery between each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      
      
      1. 

         *a	(A) Forward position
         *b	(B)
         *c	(C) Driving position
         *d	(D)
         *e	(E) Retracted position
         *f	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

         OK

         Tester Connection Condition Specified Condition z37-3 (MR) - Auxiliary battery positive (+) z37-11 (MF) - Auxiliary battery negative (-) Forward position (A) Moves from (A) to (E) z37-11 (MF) - Auxiliary battery positive (+) z37-3 (MR) - Auxiliary battery negative (-) Forward position (A) Does not move z37-3 (MR) - Auxiliary battery positive (+) z37-11 (MF) - Auxiliary battery negative (-) Position between forward position (A) and driving position (C) Moves from (B) to (E) z37-11 (MF) - Auxiliary battery positive (+) z37-3 (MR) - Auxiliary battery negative (-) Position between forward position (A) and driving position (C) Moves from (B) to (A) z37-3 (MR) - Auxiliary battery positive (+) z37-11 (MF) - Auxiliary battery negative (-) Driving position (C) Moves from (C) to (E) z37-11 (MF) - Auxiliary battery positive (+) z37-3 (MR) - Auxiliary battery negative (-) Driving position (C) Does not move z37-3 (MR) - Auxiliary battery positive (+) z37-11 (MF) - Auxiliary battery negative (-) Position between driving position (C) and retracted position (E) Moves from (D) to (E) z37-11 (MF) - Auxiliary battery positive (+) z37-3 (MR) - Auxiliary battery negative (-) Position between driving position (C) and retracted position (E) Moves from (D) to (C) z37-3 (MR) - Auxiliary battery positive (+) z37-11 (MF) - Auxiliary battery negative (-) Retracted position (E) Does not move z37-11 (MF) - Auxiliary battery positive (+) z37-3 (MR) - Auxiliary battery negative (-) Retracted position (E) Moves from (E) to (C)

         If the result is not as specified, replace the outer mirror actuator assembly RH.

   2. Check the operation of the mirror surface.

      
      
      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. Apply auxiliary battery voltage and check the operation of the mirror.

         OK

         Tester Connection Specified Condition z37-1 (MV) - Auxiliary battery positive (+) z37-10 (M+) - Auxiliary battery negative (-) Turns upward z37-10 (M+) - Auxiliary battery positive (+) z37-1 (MV) - Auxiliary battery negative (-) Turns downward z37-9 (MH) - Auxiliary battery positive (+) z37-10 (M+) - Auxiliary battery negative (-) Turns left z37-10 (M+) - Auxiliary battery positive (+) z37-9 (MH) - Auxiliary battery negative (-) Turns right

         If the result is not as specified, replace the outer mirror actuator assembly RH.

   3. Check the operation of the mirror heater.

      
      
      1. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

         Disconnect the outer rear view mirror assembly RH connector.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition z37-4 (HTR+) - z37-12 (HTR-) 25°C (75°F) 3.8 to 5.2 Ω

         If the result is not as specified, inspect the outer mirror RH or replace the outer mirror actuator assembly RH.

         Click here

      3. Connect the cable from the positive (+) auxiliary battery terminal to z37 terminal 4 (HTR+) and the negative (-) auxiliary battery terminal to z37 terminal 12 (HTR-), and then check that the mirror becomes warm.

         Tip:

         It takes a short time for the mirror to become warm.

         OK
         Mirror becomes warm.

         If the result is not as specified, inspect the outer mirror RH or replace the outer mirror actuator assembly RH.

         Click here

   4. 

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the side turn signal light assembly RH.

      
      

      1. Apply auxiliary battery voltage to the terminals of the connector, and check the illumination condition.

         OK
         Tester Connection Specified Condition z37-16 (B) - Auxiliary battery positive (+) z37-12 (-) - Auxiliary battery negative (-) Side turn light illuminates

         If the result is not as specified, inspect the side turn signal light assembly RH or replace the outer mirror actuator assembly RH.

         Click here

   5. Check the EC mirror operation.

      
      

      1. Connect a new 1.5 V dry-cell battery.

      2. 

         *a	Component without harness connected (Outer Rear View Mirror Assembly RH)
         *b	Bright
         *c	Dark

         Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

         OK
         Tester Connection Specified Condition z37- 7 (EC+) - Positive (+) end of the 1.5 V dry-cell battery z37- 15 (EC-) - Negative (-) end of the 1.5 V dry-cell battery Mirror surface becomes dark

         Note:

         Do not apply a voltage of 1.5 V or higher.

         If the result is not as specified, inspect the outer mirror RH or replace the outer mirror actuator assembly RH.

         Click here

   6. 

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      w/ Blind Spot Monitor System:

      Check the operation of the blind spot monitor indicator.

      
      

      1. Connect 4 new 1.5 V dry-cell batteries in series.

      2. Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the blind spot monitor indicator condition.

         OK
         Tester Connection Specified Condition z37- 8 (BSR+) - Positive (+) end of the 6 V dry-cell battery z37- 12 (-) - Negative (-) end of the 6 V dry-cell battery Blind spot monitor indicator comes on

         Note:

         Do not apply a voltage of 6 V or higher.

         If the result is not as specified, inspect the outer mirror RH or replace the outer mirror actuator assembly RH.

         Click here